EN

Height of Tide Calculator (Rule of Twelfths)

At low water the harbour sill is not an entrance. It is a wall, sometimes a drying bank in open air. Admiralty tide tables print four times a day: high water and low water. Between those times the question on the chart table stays the same: how much water is over that sounding now, under that keel.

The height is obtained by interpolation. Skippers have long done it in the head with the rule of twelfths, sixth by sixth. A sine curve (the old versine law) follows a clean semi-diurnal tide more closely. This page runs both, adds the charted sounding, and subtracts draught and under-keel clearance.

Tabulated heights and the soundings printed on the chart are both measured above chart datum. Depth of water = sounding + height of tide: the two add, because they share the same origin.

The two tides either side of the time wanted

Tides from the tables

High or low water, it makes no difference: the calculator works it out from the heights.

Above chart datum.

The next tide; crossing midnight is handled.

Somewhere between the two tides above.

Under the keel (optional)

Depth at chart datum. Negative for a drying patch.

Clearance kept under the keel for swell, sounding error and trim.

1.02.03.04.05.06.008:12 — 5.80 m14:30 — 1.20 m11:00 — 3.90 mm08:1209:1510:1811:2112:2413:2714:30sine curverule of twelfths
Reference diagram (sample values): the sine curve and the straight-line twelfths, split into six equal sixths. The diagram is redrawn with the figures entered once the calculation is run.

Tide-table language marked with an asterisk is spelled out in the glossary at the foot of the page.

What a charted sounding actually measures

The 3.2 printed in the fairway is not the water under the keel at four in the afternoon. It is what would remain if the sea sat on chart datum* — a reference plane, not a snapshot. In UK and Irish waters that plane is LAT*, Lowest Astronomical Tide. The sea almost never falls through it. When it does, that is a negative surge, and the tide table did not know.

Heights in the Admiralty tide tables are counted above the same zero. The charted sounding* and the height of tide therefore add, and that is the whole of the arithmetic:

Depth of water = charted sounding + height of tide

Three metres on the chart and two metres of tide is five metres of water. Drop one of the two and the keel either ploughs the putty on a quiet day, or sits waiting for a pool that is already there. A GPS plotter has no idea what LAT is. It speaks in ellipsoid height, sometimes in land levels. The chart listens only to chart datum.

That datum is not the “sea level” on a road map, and it is not Ordnance Datum* Newlyn. Between them sit mean sea level and the drop down to the lowest tides. The gap is metres on a Channel chart, much less in the Mediterranean. A bridge marked +6.20 OD is not 6.20 m above the sounding. For air draught the soffit is needed above chart datum, or a conversion. Mixing the two zeros is how a yacht “fits under the bridge, the OS map said so”.

Today's range, mean springs and mean neaps

Avonmouth at springs can show a twelve-metre range. At neaps, a third of that. Same port. Different afternoon. Range* is today's high minus today's low, not a yearly average and not a “typical” figure for the coast. It is this tide that is interpolated.

British tables talk in mean springs* and mean neaps*. The chart prints MHWS, MLWS, MHWN, MLWN — mean high and low water at springs and at neaps. Springs follow new and full moon; neaps follow the quarters, lagging a day or two because the ocean is slow to catch up. A fat spring tells two things: whether the sill opens, and whether the race will run. It does not tell the clock. The clock is the day's HW and LW.

French almanacs stamp a coefficient from 20 to 120 on the same physics — 95 a fat spring, 45 a neap — which is useful if a SHOM page is to hand. It is not what the Admiralty volume leads with. Even so, the idea is the same: amplitude is one number, time is another, and mixing them up is how a neap afternoon is treated as if it were a spring.

The rule of twelfths on a Channel tide

On the chart table the flood is sliced into six equal hours. A six-hour flood, sixty minutes each. The range is then poured 1, then 2, then 3, 3, 2, 1 twelfths. Slow at the turn, quick in the middle, slow again. A sine wave counted on the fingers — which is why the rule of twelfths* has outlived every app.

1/12  ·  2/12  ·  3/12  ·  3/12  ·  2/12  ·  1/12 of the range

After the first hour, one twelfth of the range. After the second, three twelfths. At half-tide, half the range, exactly. Most of the work is done in the middle of the interval, which is what the eye sees on any well-behaved Channel curve. Inside a sixth the interpolation is linear: if that slice carries two twelfths and half the sixth has run, one extra twelfth is taken.

It behaves on a clean semi-diurnal coast — two highs a day, a curve that looks like a bell. It gives up in a diurnal sea, in a long estuary, and anywhere the flood and the ebb do not last the same. Counting twelfths there is borrowing accuracy the water does not owe.

Cosine interpolation, and when the inches matter

This page runs both methods. The cosine form is the old versine law, the one that fits on the back of a logbook:

h(t) = (h₁ + h₂)/2 + (h₁ − h₂)/2 · cos( π · (t − t₁) / D )

h₁ and h₂ are the heights of the two tides that bracket the instant t; D is the interval between them. The cosine starts at 1 at the first tide (h₁ comes back) and reaches −1 at the second (h₂). Between those ends the curve is smooth. Twelfths draw a six-segment broken line, faster in the head, a little more angular on the plot.

Mid-flood, the two sit within a couple of percent of the range. Near high and low they can drift toward 5%. On a 4 m range that is twenty centimetres. Nothing at a deep-water berth. Everything on a sill where inches are already being stolen. Twelfths will do for a sketch. The sine is for a tight gate — and only if the harbour's curve is actually a sine.

Under-keel clearance on rock, sand and mud

Draught* is what the boat sticks in the water. Under-keel clearance* is what is added because the world is not a millpond: swell, a sounding that was a hole next door (charts round, sediment moves), a cockpit locker full of wet warps. For a cruising yacht, 0.5 to 1 m is a starting point, not a religion. Rock, take more. Soft mud, the margin can be shaved. Sand sits in between.

The nature of the bottom also changes what “touching” means. Rock breaks a keel. A mudflat stops the boat, often with no harm beyond a wait. Under-keel clearance is therefore not the same thickness over a charted R, S or M. It is not the same thickness in today's swell either: 80 cm of chop in a gut already eats more than a habitual half-metre margin.

Air draught* is the same game upside down. A bridge, a cable, a clearance quoted above chart datum. Rising water eats the gap. Height of tide wanted for the keel can be the height that stops the mast under the span. An “aerial” margin is not a luxury if there is swell under the soffit, or if the mast is hanging off a reefed sail.

Clearance on this page is depth of water minus draught minus the margin entered. A negative result means there is not enough water, even in a flat calm. The form does not argue with the bottom, the trim, or today's residual.

A harbour sill is a time window

Off a harbour sill*, the useful question is not “how much at 15:00?”. It is “from when is 1.8 m of tide there, and until when?”. The metre belongs to an anchorage. The clock belongs to the passage.

  1. Fix the least depth that will be accepted: draught plus under-keel clearance, plus a lump if the bar is standing up.
  2. Find, on the flood, the time that depth is first reached.
  3. Find, on the ebb, the time it is lost. Between those times, the gate.

A drying harbour on the Wash. The sill is charted at 0.0 m. Draught 1.3 m, under-keel clearance 0.5 m. 1.8 m of tide is required. Neaps. LW 05:00, 0.7 m. HW 11:00, 4.3 m. Range 3.6 m, six-hour flood. From low water the rise still needed is 1.1 m.

First sixth (05:00–06:00): +1/12 of 3.6 = 0.30 m. At 06:00 the height is 1.00 m — still short. Second sixth: +0.60 m, which brings 1.60 m at 07:00. Still 0.20 m short. Third sixth: +0.90 m over 60 min. 0.20 / 0.90 × 60 min ≈ 13 min. The gate opens at 07:13.

Rise needed = 1.8 − 0.7 = 1.1 m  ·  0.30 + 0.60 in the first two hours, 0.20 m into the 3rd → 07:13

The window lasts until the ebb drops back through 1.8 m — the same sums run backwards from 11:00. At neaps it can be under an hour. Miss it and the wait is six hours, or twelve. Without the secondary-port line, if there is one, and without the surge bulletin, 07:13 remains a paper time, not a channel time.

Time for a given height

H is known, t is wanted. That is the sill calculation, the one actually done with a pencil in the cockpit, more often than “how much water at 11:00”. With the sine curve the cosine is inverted:

t(H) = t₁ + (D / π) · arccos( 2 · (h − (h₁ + h₂)/2) / (h₁ − h₂) )

The result only exists if h lies between h₁ and h₂. Outside that band the height wanted is never reached in the interval — the usual fate of a neap against a high sill. With twelfths, 1/12, 2/12, 3/12 are piled up until the required rise is passed, then the time is interpolated inside that slice. That is exactly what the Wash example did by hand.

Height at a time is for an anchorage, a grid, a dinghy that may or may not still float. Time for a height is for getting in. Both are read from the same curve; only the axis changes.

Drying out and floating off

A hard sand beach, a grid, a drying harbour. The keel is put on the bottom on purpose. Clean ground, a boat that stands — long keel, legs, or a lifting-keeler with the plate up — and a low water low enough to work. Drying out* is not a grounding. It is an appointment with the bottom, made the day before on the chart and in the tables.

The arithmetic, at the start, is the sill in reverse. From what time does the water beat the draught, plus enough to start the engine and slip? Twelfths put the answer inside ten minutes if the curve is polite. Lines are not let go on the minute. The engine is warmed, warps let go, the gut cleared before the ebb. A good drying-out is a bottom chosen the day before, not a formula.

The tide also has to fall far enough. On neaps, a boat drawing 1.6 m on a grid that dries to 1.4 m above datum will never sit. Today's range decides as much as the clock. And floating off is calculated on the next tide, not the one that took the ground: six hours later the range is already a little different, especially around building springs.

Height of tide is not the stream

A big spring lifts water. It also runs the race. Portland Race, the Alderney Race, the Swinge: today's range says 3 knots or 6. The form only adds metres. For the course to steer, that is the other calculator, and a tidal-stream atlas for the same day, the same springs or neaps.

Slack is not always at high water. Up a river the stream can still be ebbing while the level is already rising. Height and stream are two clocks. Crossing a sill “at slack” only helps if slack at that place coincides with the depth wanted — which, in an estuary, it rarely does.

One last, duller trap: copying the table. Admiralty times are usually UT (GMT). In summer the clock in the wheelhouse is BST, one hour on. Heights in metres in the modern volumes; older reprints still in feet. HW and LW, not a phone app that rounds the tide to the nearest half hour and calls it “high around lunch”. The four numbers of the day — time and height of the tide before, time and height of the tide after — are enough. One line too low in the table is a sill that never was.

Standard ports and secondary-port differences

The Admiralty volume prints a handful of standard ports* in full: Portsmouth, Dover, Devonport, London Bridge, a few dozen others. Everything else is a secondary port* — plus or minus so many minutes on HW*, a different number on LW*, and height differences that are not the same at springs and at neaps. “Portsmouth + 20 min, −0.3 m at MHWS” is a recipe, not a poem. The column that matches today's range is the one that counts.

A secondary-port correction is geography. It is the time the wave takes to travel up a harbour, the squeeze of a narrows, a bank that slows the flood. It does not include today's wind. Mix the two and the sill “opens” half an hour early on paper. Ten miles from the standard port, twenty minutes looks like nothing. Off a narrow gut, the stream has already turned.

Differences on LW can carry the opposite sign to those on HW. Both lines have to be read. And the time difference at high water is not a licence to shift the whole curve by that amount: the duration of rise may change as well, which is why a secondary port with a very different flood-to-ebb ratio deserves its own local curve, not a shifted Portsmouth.

Solent stand, double high water, tidal rivers

Southampton Water holds a high-water stand. The Solent can throw a double high. Poole does something similar. The tide climbs, hesitates, dips, climbs again. Six equal sixths do not live there. Interpolating between “the” LW and “the” HW has no meaning: there are three or four turning points, and the pair to enter is the pair that actually brackets the time wanted. A table that prints only two is not enough.

Up a river — Thames, Severn, Mersey — friction, freshwater and the narrowing chew the wave. Range changes in a few miles. A tidal bore is not a sine. Once the chart or the almanac mutters “see special curve”, the twelfths go back in the drawer and the hourly heights for that place come out, not those of a standard port twenty miles seaward.

The East Coast has its own manners. A young flood stand on the Thames, a long wait over the banks of the Wash, a bar that only pays on the last of the flood. Local tide curves, and the harbourmaster's board, beat a Day Skipper rule of thumb.

Residuals: the table has no weather

The table is astronomy. The sea also listens to the sky. A 1 hPa drop lifts the water about a centimetre — the inverted barometer, a rule of thumb, not a laboratory law. A 980 hPa low is thirty or forty centimetres of surge* before the wind even starts. A fat high does the opposite: a negative surge, a residual the wrong way. Onshore wind piles water on the beach; offshore wind strips it. In a funnel, a metre has been seen.

That said, adding 40 cm “because there's a low” with no forecast is wishful. The UKHO* and the Met Office publish residuals, port by port or by stretch of coast. Those are laid on the astronomical height. They are not invented to talk a keel over a sill. A positive surge helps on the way in; the same surge, that evening, can stop the mast under a bridge. The sign of the residual is not always the sign hoped for.

In practice this page interpolates the astronomical tide. A 30 cm negative surge on an already tight passage wipes out the under-keel clearance. A surge of the same size, with an onshore wind and a mud bottom, is not a licence to shave the margin: the swell that comes with it has often already taken those thirty centimetres back.

Glossary

Chart datum
The reference plane for depths on a nautical chart. In UK and Irish waters it is LAT. Charted soundings and tabulated heights of tide are both measured from this same plane.
LAT
Lowest Astronomical Tide: the lowest level the tide can reach under the gravitational pull of sun and moon alone, with no wind or pressure. Chart datum on modern British charts.
Sounding
The depth printed on the chart, from chart datum down to the seabed. A negative (underlined) figure is a drying height: the bank uncovers at low water.
Ordnance Datum
The land levelling system of Great Britain (Ordnance Datum Newlyn). It does not share an origin with chart datum. A quay or bridge quoted in OD is not that many metres above the sounding.
Range
The difference in height between a high water and the low water that brackets it, for this tide. Not the mean range of the port, and not a coefficient.
Springs
Tides of large range, around new and full moon. Mean High Water Springs (MHWS) and Mean Low Water Springs (MLWS) are printed on the chart. Streams run hardest then.
Neaps
Tides of small range, around the moon's quarters. A sill that opens at springs may stay shut all day. Mean High / Low Water Neaps: MHWN, MLWN.
Rule of twelfths
A mental approximation of the tidal curve: the range is shared out 1, 2, 3, 3, 2, 1 twelfths over the six equal sixths of the interval between two successive tides.
Standard port
A port for which the Admiralty tide tables print daily times and heights of high and low water. Other harbours in the area are derived from it by differences.
Secondary port
A harbour without its own daily prediction. A time difference and a height difference (often separate at springs and at neaps, and at HW and LW) are applied to its standard port.
HW
High water: the time of the highest height of tide in the cycle, and that height itself.
LW
Low water: the time of the lowest height of tide in the cycle, and that height itself.
Draught
The vertical distance from the waterline to the lowest point of the hull (keel, bulb, plate down). What the boat “sticks in”. American spelling: draft.
Under-keel clearance
The safety margin kept under the keel, on top of draught. It covers swell, sounding error, trim and the tables being a little out. It is chosen for the bottom and the day, not once for all.
Air draught
The height of the highest point of the boat above the waterline (mast, aerial, arch). Compared with a bridge or cable, itself reduced to chart datum.
Harbour sill
A shoal, cill or cill-stone that bars the entrance to a harbour or basin. It is passable only when the depth of water exceeds draught plus under-keel clearance. Also spelled cill on lock gates.
Drying out
Putting the keel on the bottom on purpose as the tide falls (beach, grid, drying berth). Floating off is the sill problem in reverse: the time the water takes the boat again.
Surge
The residual: the difference between the observed level and the astronomical tide, caused by pressure, wind or a storm wave. Positive (a surge) or negative. Published, not guessed.
UKHO
United Kingdom Hydrographic Office. It publishes Admiralty charts, the Admiralty Tide Tables, and the standard-port / secondary-port differences used around these islands.

Related calculators