Calculate a Quarter-Turn Staircase: Landing or Winders
A quarter-turn staircase changes direction by 90° somewhere between the lower and upper floor — either through a flat landing, or through winders that pivot around a newel post. Pick a layout in the tabs below: the rise stays the same throughout, but the run — and so the comfort of the stair — is worked out differently on either side of the turn.
For the same total rise, a landing costs floor space but gives a real breather partway up; winders save space but pinch the run near the newel. Both tabs share the same target rise (around 17 cm / 6¾ in) and the same rule of thumb for a comfortable step (2 × rise + run ≈ 63 cm / 25 in).
Staircase dimensions
Two straight flights joined by a square landing. The rise is shared across both flights; the run is worked out separately on each one.
The turn is treated as a 90° sector centred on the newel post. The walking line is fixed 0.50 m (about 20 in) from the inner string; each winder occupies an equal angle.
Trade terms marked with an asterisk are defined in the glossary at the foot of the page.
What the stairwell can take: quarter-landing versus kite winders
A right-angle stair is the default of the suburban house and the Victorian terrace alike. One corner, ninety degrees, then a second flight. The trade name is quarter-turn; the choice on the drawing is a square quarter-landing* or a pack of kite winders*. Neither is a U-turn, and neither is a helix around a pole.
A straight flight wants length. Most halls do not have it. They have a corner, often beside the front door, and the L is the geometry that keeps the sitting room in one piece. Rise does not care which drawing is chosen: storey height divided by the number of risers. What cares is the footprint, and what the foot does at the corner.
A landing eats plan. Ninety centimetres of stair width means a 90 × 90 cm square that does no climbing, plus the two goings L1 and L2. Fine in a new-build hallway. Tight in a terrace where the bathroom already sits behind the turn, or in a loft conversion where that square would steal the shower. Winders spend the turn as rise: every degree of rotation also climbs. In the worked numbers further down, the same storey height sits in a rectangle up to 75 cm shorter on one axis — a good deal less on the other, depending on where the newel* bites hardest.
Still, a landing is where the sofa goes down for a minute. Winders offer no rest, and the inner corner is a sliver. Where the hall has room, the landing wins. Where the hall is the constraint, winders — provided they are set out, not guessed in the leftover triangle.
Newel, inner string, or a centre on the setting-out rod
The second tab puts a black dot at the inside corner. Every kite radiates from it. On site that dot is not always a piece of timber one can knock.
- Newel post — turned timber, a steel tube, sometimes a masonry stub. The radius typed here (often 50–150 mm) is half the post. Tread nosings die into it.
- Inner string — a closed string or a cut string hugging the corner, no post on show. The “newel radius” is then the distance to the inner face of that string*. A 40 mm string glued into the angle is not a 40 mm newel: the useful radius is smaller, and the inner going* collapses.
- A point on the rod — concrete stairs, a single outer string, two walls meeting. There is no post. A centre is invented anyway so the angles share fairly. The arithmetic does not care. The joiner does.
An 80 mm radius, three kites, 900 mm width: inner going about 42 mm. Nobody plants a heel there. Fatten the newel first. Adding treads will not save the pinch.
Where the going is measured: 270 mm, 12 in, or 500 mm
Nobody walks the centre of a wind. The hand looks for the inner rail; the body leans in. This calculator, matching its continental sister pages, parks the walking line* 500 mm off the inner string. That is not the only convention in the English-speaking world, and it is not the one a building-control officer in England will quote first.
Approved Document K* measures the going of a tapered tread 270 mm in from each side. The IRC walk line sits 12 in (about 305 mm) off the narrow end, and wants 10 in of going on that line, 6 in minimum anywhere. On an 800–900 mm private stair those three lines are not far apart. On a 1.20 m public stair they diverge, and a 500 mm line sits closer to the inner rail than a centre-line would.
rwalk = rnewel + 0.50 m · going(r) = (π/2 × r) ÷ winders
This page always uses 500 mm. An 800 mm flight therefore has the walk 500 mm from the tight edge and 300 mm from the wall. Not centred. On purpose. 2R + G, the derived L1 and L2, the comfort test: all of that uses the going on that line. Inner and outer goings are warnings, not the number the timber is cut to. A drawing headed for English building control is measured again at 270 mm before anyone cuts.
A kite winder has three goings, not one
A square tread has one going. A kite is a triangle or a trapezium. The nosing is a radius. Going grows as one leaves the newel. Tight at the post, honest at the walking line, generous at the wall.
The page flags anything under 10 cm (about 4 in) at the inner string, and anything over 45 cm (about 18 in) at the outer. Ten centimetres is a heel. Less than that, and the person hugging the newel with a laundry basket has nowhere to put a foot. Forty-five centimetres at the wall is a stretched stride for anyone who walks wide — a child, two people passing. The calculator does not lock those values out. It paints them red. A comfortable kite is three goings in a band, not one magic number.
Only the walking-line going goes into 2 × rise + going. That is the figure matched to the straight flights. The other two keep the foot from vanishing, or from over-reaching.
Three, four or five kites: comfort versus pinch
Three is the shop habit. A right angle, three 30° slices. The nosing stays readable, a concrete former remains simple, a timber string cuts without a skip of waste. Four means 22.5° each. Five, 18°. This form stops at six: more than that and the layout is no longer a quarter-turn, it is a slice of spiral.
People add winders to “open the pinch”. They do the opposite. Ninety degrees is fixed. More slices, thinner slices, smaller inner going. Three treads on an 80 mm newel: 42 mm at the post. Five treads: 25 mm. Extra winders help the outer going — it shortens, one stays under 45 cm — and can tame a walking-line going that had grown long. They do not rescue the pinch.
The lever for the tight edge is newel radius. A 260 mm radius, four kites, 800 mm width: roughly 102 mm inside, 298 mm on the walk, 416 mm at the wall. Liveable. An 80 mm post and three treads “because that is what the last house had”: not liveable.
How big a quarter-landing has to be
On this page the landing is a square whose side equals the flight width. 800 mm stair, 800 × 800 landing. 900 mm, 900 square. That is the private-stair minimum in a lot of guidance: do not make the rest narrower than the flight. A public stair, an accessible dwelling, a Part M conversation — different drawing. Then there has to be room for a wheelchair to turn, often a 1.20 m circle or a 1.20 × 1.50 m rectangle, and a rail that does not steal it.
Fire is another brief. In a block stair the landing is a storey landing, a hold point, sometimes a lobby. This calculator sizes a house L, not a protected shaft. Once a landing opens onto a fire-resisting corridor, a joinery page is the wrong document: the fire strategy speaks.
An 800 × 800 mm landing is not an accessible landing. A wheelchair does not turn on it, and winders are simply off the table on an accessible route.
Three jobs, three answers. Ordinary house — square of the width. Accessible — enlarge it, or drop the quarter-turn. Fire / public — leave this page.
A continuous handrail around a 90° newel
The hand does not let go. That is the whole rule, and it is the one shops break. A fat corner newel, an 80 mm gap between two rails, a return that makes the hand swap mid-wind: the body unhooks just where the tread is least kind.
On a landing the rail follows the L. It may break at the landing if the landing guarding picks up — provided the hand finds the next stick without hunting. On winders the inner rail is a quarter-circle (or a polyline that fakes one), sharing the newel with the treads. Its radius is not the walking-line radius. It sits closer in, at grasp height, against the string or the post. The outer rail has further to travel for the same 90°, so its pitch is gentler than the treads. The two are not parallel in section. Cut them from the same stock and twist them round the corner, and the result is a chewed mitre and a knuckle on the newel.
Height, about 900 mm above the nosing. One side is often enough in a narrow private flight, inner side preferred, because that is where one holds. Both sides once the flight widens, or once strangers use it.
Worked example: 2.50 m of storey height
Ceiling 2.50 m, 200 mm floor structure, floor to floor is 2.70 m. The working figure is 2.50 m of rise: the low ground floor, or the “ceiling equals upper floor” sketch. Fifteen risers at 167 mm. Blondel’s formula* wants a going near 300 mm.
With a landing
Eight treads, 2.40 m going, 300 mm run. Then a 900 mm square. Then seven treads, 2.10 m going, 300 mm again. Step length 2 × 167 + 300 = 633 mm on both flights. Footprint 3.30 m × 3.00 m. The landing sits 1.33 m up. Typical estate-house L, and it fits an 11 m² hall if a coat stand is not parked in the square.
Winders
Same height, fifteen risers again, split 5 straight + 4 kites + 6 straight. Width 800 mm, newel radius 260 mm. Inner going 102 mm, walking line 298 mm, outer 416 mm. L1 and L2 come out at 1.49 m and 1.79 m. Footprint around 2.55 m × 2.85 m. 75 cm back on one axis, barely 15 cm on the other, paid for with an inner edge sitting on the 100 mm line.
R = 2.50 m / 15 = 167 mm · 2R + G ≈ 630 mm when G ≈ 300 mm
The landing tab with the default 7 and 6 treads on 2.40 m and 2.20 m: rise 192 mm, too tall for a main stair, goings still decent. Count of risers sets the steepness, not the length of hall.
The going that jumps between the straight flight and the wind
The drawing that was sized as a straight stair, 280 mm going, then had three kites squeezed into the leftover corner. On the walking line the turn comes out at 220 mm, or jumps to 360. The foot has already learned a cadence. At the wind it trips, or it shuffles, and it is always the same tread that wears.
The winder tab will not let that split happen. It finds the walking-line going first, then derives L1 and L2 (L = n × going). A straight-flight length that would force a different going cannot be typed in. That is the point. The landing tab leaves L1 and L2 free — two straight flights may differ — and warns if the goings drift more than 15 %.
Twin mistake: a rise that changes after the landing. Eight at 170 mm, landing, six at 190 mm because “there was height left”. That is the moving-day spill. One rise, the whole way, landing included. A landing is not a tread. It does not add a going. It does not forgive a taller riser afterwards.
Quarter-turn, half-turn, spiral
A quarter-turn is one 90° corner, low, mid or high. A half-turn comes back on itself, with a half-landing or two packs of winders, flights parallel. A spiral has no straight flight: every tread is a winder around one newel, through 360° or near enough.
This page does the L. Not the U, not the helix. A well that forces a 180° return is not this calculator run twice: stacking the heights produces a Z, or a return that is not parallel. Three tools, three footprints. The tool is chosen before the stringer is cut.
Equal angles are not a full winding drawing
Each kite here takes the same angle. A sector of a spiral, clean, easy to check, already better than three pointed boards jammed in a corner. A staircase workshop often “steals” one or two straight treads on each side of the turn, so the inner going opens gradually instead of jumping from a rectangle to a triangle in one nosing.
Fair enough if the equal-angle inner going lands on 100 mm: a proper winding drawing may pull it to 120 or 130, at the cost of a shop rod. This page sizes the sector. It does not replace the stringer’s setting-out.
Headroom in an L-shaped well
The landing tab calculates headroom under the well of the upper flight. Same reasoning as a straight stair: plumb from the nosing to the soffit, often aiming at 2.00 m. The turn dirties the hole. A rectangular opening “as if it were straight” leaves the outer string of the quarter in the floor, or opens the sitting room too far. The hole follows the L, or at least a rectangle that contains the L.
On winders, headroom is judged on the walking line, not at the newel. Beside the post the head is elsewhere, and the ceiling is often further off — under the room, not under the well. It is at the wide edge, and at the start of the upper flight, that a beam is hit. The first tread is set back, the well is enlarged, the floor thickness is reduced if the structure allows. Not “heads will be ducked, one gets used to it”.
Glossary
- Quarter-landing
- A square rest at the corner of an L-shaped stair, usually with a side equal to the flight width. It lets a person stop and change direction without tapered treads.
- Kite winder
- A triangular or kite-shaped tread whose going varies from the inner string to the outer. A pack of kites turns the stair 90° without a landing.
- Newel
- The centre of the turn: a post, the inner face of a string, or a point on the setting-out. All the kites radiate from it.
- String (stringer)
- The sloping member that carries the treads. In a quarter-turn the inner string follows the corner; the outer string is longer.
- Going (run)
- Horizontal distance from nosing to nosing. On a kite there is not one going: inner, on the walking line, and outer.
- Walking line
- The path actually walked. This page uses 500 mm from the inner string. Approved Document K measures tapered treads 270 mm in from each side.
- Approved Document K
- The English guidance behind Part K of the Building Regulations (protection from falling, collision and impact). It sets private-stair limits on rise, going and 2R+G, and where a tapered going is measured.
- Blondel’s formula
- The relation 2R + G ≈ 630 mm, taken from an adult stride. It judges a rise/going pair; it does not say how many risers a storey needs.