EN

Current Divider Calculator (Multiple Resistors)

In a network of parallel resistors, the total current splits between the branches in inverse proportion to their resistance: the least resistive branch gets the largest share of the current. Unlike a voltage divider, it's not the ratio of resistances that matters, but the ratio of conductances (the inverse of resistance).

Enter the total incoming current and the list of parallel resistors — two or more — to get the current through each one, the network's equivalent resistance, and the voltage across it.

The network

Total current and resistors

2 to 20 strictly positive values, separated by a comma or a space.

Why current splits inversely to resistance (and not like a voltage divider)

Parallel branches share one voltage. Ohm's law then does the rest: I = V/R, so the small resistor takes the large current. That is the opposite of a series voltage divider, where the large resistor drops the large voltage. Same three letters, different geometry.

I ∝ 1/R is the whole idea. “Current takes the path of least resistance” is not a proverb here — it is the formula.

Deriving the formula from the shared voltage across the network

n resistors in parallel, total current Itot. One voltage:

V = Req · Itot   ·   1/Req = Σ 1/Rᵢ

Branch k then draws Ik = V / Rk. Substitute V and you have the divider:

Ik = Itot · (Req / Rk) = Itot · (1/Rk) / Σ(1/Rᵢ)

Kirchhoff's current law is satisfied automatically: the Ik add back to Itot. If they do not, you mis-copied a resistor.

Special case of two resistors: I1 = Itot · R2/(R1+R2)

Two branches is the form everyone memorizes — and the one that looks like a voltage divider with the resistors swapped.

I1 = Itot · R2 / (R1 + R2)   ·   I2 = Itot · R1 / (R1 + R2)

The other resistor sits in the numerator. R2 large → most of the current through R1. Equal resistors: half and half, every time.

Conductance: why it's the right quantity to add in parallel

Conductance G = 1/R, in siemens. Parallel elements add as conductances, the way series elements add as resistances. The divider then reads as a share of G:

Geq = Σ Gᵢ   ·   Ik = Itot · Gk / Geq

Once you think in G, five parallel branches are no harder than two. The page's formula is that sentence with 1/R written out.

Current dividers and ammeter shunts

A moving-coil meter wants milliamps. A shunt Rsh across the movement (Rm) steals the rest. If the meter should see 1/n of the circuit current:

Rsh = Rm / (n − 1)

A 1 mA, 50 Ω movement made into a 10 A meter needs a 5.0005 mΩ shunt — which is why shunts are four-terminal hunks of manganin, not a stripe on a colour-coded resistor. The divider law is the same; the power is not.

Current sharing in parallel LED strings: the pitfall to avoid

One resistor, several LEDs in parallel: the die with the lowest VF hog the current, runs hot, VF falls further (negative tempco), and you get thermal runaway. One series resistor per LED is the fix, not a “matched” batch from the same reel.

Power LEDs in parallel want a current source per string, or a ballast resistor large enough that VF scatter is a small fraction of the ballast drop. A milliohm of copper is not that ballast.

AC current dividers: replacing R with an impedance

In sinusoidal steady state the same algebra holds with complex Z:

Ik = Itot · Zeq / Zk

At one frequency a capacitor is 1/(jωC), an inductor jωL. The “small resistor” is then the small impedance — a capacitor at high frequency takes the current, which is exactly a bypass. Phasors, not a new law.

Common mistakes: applying the voltage divider formula by mistake

  • Series, voltage — V1 = Vtot · R1 / (R1+R2). Own resistor on top.
  • Parallel, current — I1 = Itot · R2 / (R1+R2). Other resistor on top.

The two lines look like cousins. They are not interchangeable. If the current you computed is larger in the larger resistor, you used the voltage formula on a current problem.

Equal resistors and an N-way split

n identical branches: each takes Itot / n. Two 10 kΩ and one 5 kΩ is not “three ways” — the 5 kΩ is two of the 10 kΩ in parallel, so it takes half the total, and each 10 kΩ takes a quarter. Sketch the conductances before you trust a hunch.

Load sharing between power supplies

Two bench supplies in parallel are a current divider whose “resistors” are the output impedances plus any ballast you add. Without ballast, the supply with the slightly higher voltage dumps most of the current. A small series resistor on each (0.1–0.5 Ω, sized for the drop) is the same trick as the LED string, with more watts.

Thevenin, Norton and which picture to draw

A current divider is the natural view of a Norton source (IN in parallel with RN) feeding extra parallel loads. Convert to Thevenin if you care about voltages. The numbers do not change; the diagram you reach for does. If the source is a voltage behind a resistor, convert first, then split — do not apply the current formula to a series chain.

The two-resistor current formula has the other resistor in the numerator. Copying the voltage-divider line and changing V to I is the most common arithmetic error on this page, and it is always wrong by a swap of R1 and R2.

Related calculators