EN

Solution Concentration & Dilution Calculator

Hospital pharmacies hang a surprising amount of work on one figure: 0.9% sodium chloride. Nine grams per litre, 154 mmol/L, close to the osmolality of plasma. The same arithmetic returns at the bench: the mass to weigh for a stated concentration, the aliquot to take from a stock, the conversion among mol/L, g/L, ppm and percent.

Adding solvent does not add solute. Volume grows; amount of substance stays. Hence C1V1 = C2V2, and the graduation mark that fixes the final volume — rather than pouring “250 mL of water onto the solid” and hoping the total is 250 mL of solution.

Mode and data

Type of calculation

Change mode, then run the calculation again to update the fields.

Preparing a solution — n = C × V and m = n × M

Whatever you type for this quantity is ignored.

Don't know it? Work it out with the molar mass calculator.

Result

  • Mass of solute to weigh m 1.4610 g
Molar concentration C 0.10000 mol/L
Mass concentration Cm 5.8440 g/L
Amount of substance n 0.025000 mol
Mass of solute m 1.4610 g
Volume of solution V 250.0000 mL (0.25000 L)
Molar mass M 58.440 g/mol

m = n × M = C × V × M

Terms marked with an asterisk are defined in the glossary at the foot of the page.

Making up a solution in a volumetric flask

The working sequence is short. It is also where the concentration on the page and the concentration in the bottle part company, if a step is skipped.

  1. Find n = C × V, with V in litres (0.250 L, not 250 left sitting in the formula as if it were litres).
  2. Weigh m = n × M. For 250 mL of 0.1 mol/L NaOH, n = 0.025 mol and m = 1.00 g (M = 40.00 g/mol).
  3. Dissolve in a little solvent, transfer quantitatively, and make up to the mark*.

Water is not poured onto the solid until the beaker reads 250 mL. Final volume is not a sum. Fifty millilitres of ethanol plus fifty millilitres of water occupy a little less than 100 mL once the mix is back to room temperature: the molecules pack. Concentrated sulfuric acid shrinks more, and heats. That is what the mark is for — a single line on a narrow neck, meniscus tangent, eye level.

A volumetric flask is not a beaker. A 250 mL class-A flask is tolerated to about ±0.15 mL, 0.06% of the volume. In other words, glassware error, if the mark is read properly, is smaller than the weighing error on a gram of sticky NaOH. Pellets take up water; the 1.00 g in the notebook is a theoretical mass. Analytical work titrates afterwards. A hospital pharmacy starts from assayed material, or from a concentrated ampoule whose strength is stated.

Quantitative transfer is not a teaching ritual. Solid left in the weighing boat, drops in the funnel: concentration lost. Three rinses into the flask, then make up. Making up before everything has dissolved leaves a grain on the bottom and a volume already “correct”. The titre is low until the grain goes in later, at which point it is high.

Molarity: C = n / V is solution volume, not solvent volume

A solution is not a heap of powder next to a jug of water. It is a solute* dispersed in a solvent*, occupying a volume of solution. The distinction barely matters at 10−3 mol/L. It matters as soon as C is high, the solid takes up space, or two liquids contract on mixing.

Molarity* counts moles per litre of solution. Equations, assays, equilibrium constants all use it. Bottle labels more often show grams per litre. The bridge is the molar mass M, in g/mol — the figure the molar-mass calculator returns from a formula.

C = n / V  ·  n = m / M  ·  Cm = C × M

V is the volume of the finished solution, not the volume of water poured onto the solid. 10.00 g of NaCl (M = 58.44 g/mol) in a 1.000 L flask gives n = 10.00 / 58.44 = 0.1711 mol, so C = 0.1711 mol/L and Cm = 10.00 g/L. Running the same arithmetic backwards is the daily gesture of preparation: n = C × V, then m = n × M.

Worth noting: molarity drifts a little with temperature, because volume expands. At a 20 °C bench the shift is small. For a concentrated liquor, or for a quantity that must not care about the thermometer, molality is the other handle.

Dilution without losing solute: C₁V₁ = C₂V₂

Dilution adds solvent, not solute. The amount of substance taken from the stock solution* is the amount that ends up in the daughter flask. n1 = n2, so C1V1 = C2V2.

C1 V1 = C2 V2

A tenfold cut. Stock at 1.00 mol/L, daughter at 0.100 mol/L, final volume 100.0 mL. V1 = C2V2 / C1 = 10.0 mL. Ten millilitres are pipetted into a 100 mL flask and made up to the mark. The “90 mL of water” is not measured in a cylinder. It does not need to be 90.000 mL: the final volume is the one that is made up, not the solvent added.

C1 and C2 may be mol/L, g/L or ppm, provided both sides use the same unit. The dilution factor f = V2 / V1 = C1 / C2 is dimensionless. A 1-in-10 is f = 10, not “take off 10%”.

Molarity versus molality

Molarity counts moles per litre of solution. Molality* counts moles per kilogram of solvent. In dilute water the two look alike: a litre weighs about a kilogram, and the solute hardly weighs. In 200 g/L glucose, or in a strong acid bath, the gap is measurable.

Molality does not care about temperature. Solvent is weighed, solute is weighed, the ratio holds in a freezer and in a water bath. Freezing-point depression, concentrated-solution thermodynamics: molality. Pipettes, flasks, burettes, infusion bags: molarity, or % w/v, because a volume is what gets measured.

This page computes C = n / V. It does not convert to molality; density would be required. Treating “0.1 molal” as “0.1 mol in 1 L of water” is harmless in very dilute aqueous work and wrong in a syrup.

ppm, mg/L and % w/v: what labels actually mean

Trace work has its own dialect. Tap water, a metal residue, a food preservative: mol/L give way to milligrams per litre, ppm*, % w/v*.

In dilute aqueous solution, 1 ppm ≈ 1 mg/L. The equality holds because a litre of water weighs about a kilogram, and one part per million by mass is 1 mg in 1 kg. In oil, in ethanol, in brine at 200 g/L, the density is no longer 1.00 g/mL. The shortcut dies. A ppm “in petrol” is not a mg/L.

Pharmacy % w/v counts grams of solute per 100 mL of solution. Normal saline at 0.9% w/v is 0.9 g in 100 mL, hence 9 g/L. That is not 0.9% by mass (0.9 g per 100 g of solution) and not 0.9% by volume. Three percents, three different preparations. In other words, a bare “%” on a label is not a number a calculation can use.

Crossing into molar units needs M. 9.00 g/L of NaCl, M = 58.44 g/mol, is 0.154 mol/L. The conversion mode on this page does that bridge. That said, “ppm” with no “of what” — mass, volume, moles — is a sales word. Here ppm = mg/L, aqueous, dilute. Drinking-water convention, not a law of physics.

Bulb pipette versus measuring cylinder

A 10.00 mL bulb pipette is not a cylinder marked “about 10”. The pipette has one line, a delivery time, a class-A tolerance around ±0.02 mL. The cylinder has a painted scale on thick glass, read to 0.1 or 0.2 mL, worse if the meniscus is viewed off-axis.

A tenfold dilution done in a cylinder, C2 to 5%: common enough. For an assay, the flask and pipette. For a rinse bath or a plant-feed mix, the cylinder saves three minutes. The craft is knowing which job is on the bench — not putting every litre into a volumetric flask, and not putting a calibration standard into a cylinder.

The pipette is held vertical. Blowing out the last drop to “finish” is a cylinder habit. It changes the volume. The flask is brought to the mark with a wash bottle, drop by drop, after inversion — not shaken like a cocktail, which wets the neck above the mark and spoils the reading.

Acid into water, never the other way

Heat of dilution is not a textbook aside. Water poured onto concentrated sulfuric acid dumps the heat into a thin layer of water, which can boil and spit acid. Acid poured into a body of water already present, with stirring, spreads the heat through the whole mass. Same n, same final V, no spray.

Concentrated acid: acid into water, never the reverse. Heat of dilution spatters. And volume is not additive: the mark again, once the mix has returned to the temperature of the glassware.

The mark is read at the calibration temperature, in practice 20 °C. A flask still hot after an acid dilution shows a volume that is too large (glass and liquid have both expanded). Wait. Then make up. Filling to the mark at 40 °C because “it looks right” delivers a titre that is too high once the bottle has cooled.

HCl, HNO3, H2SO4: the same order. Strong bases heat as well, enough to burn. Goggles, gloves, fume hood. The arithmetic on this page does not stand in for the reagent safety sheet.

Normal saline 0.9%: a hospital number that sits in the formula

Nine grams a litre. That is all “normal saline” is. 0.9% w/v NaCl, M = 58.44 g/mol, C = 9.00 / 58.44 = 0.154 mol/L, 154 mmol/L. The salt dissociates: 154 mmol of Na+ and 154 mmol of Cl−, about 308 mosmol/L, in the plasma range.

The figure is not a charm. It is chosen so red cells neither burst nor shrivel. Half-normal saline (0.45%) is hypotonic; 3% is a hypertonic bolus, a different job. A 500 mL bag at 0.9% holds 4.5 g of NaCl. In an aseptic unit the titre is checked, the pH recorded, sterility signed off. The weigh-out is only the first line of the batch record — but a bag labelled 0.9% and made at 8.1 g/L is no longer saline.

Serial dilutions when the factor is large

A thousandfold cut in one step means 0.100 mL into a litre. Poor practice. Two 1-in-10 dilutions and a third, each with a pipette and a flask that match the volume, stay inside volumetric glassware. That said, every extra step is another chance to grab the wrong flask. Two clean stages beat four stages “on principle”.

The relative errors multiply, but they remain class-A errors, not the error of a micropipette used outside its range. For a colourimetric assay the last flask is the one that goes into the cuvette; the stock concentration is recovered by multiplying back by f.

From the flask to the assay: pH and absorbance

Once the solution is in the flask, two questions tend to follow. What is the pH? And, if the species is coloured, what absorbance will the spectrophotometer read?

The concentration calculated here is the input to the pH scale: a strong acid at 0.010 mol/L is pH 2.00 at 25 °C, provided water itself is not already contributing as much H3O+. Diluting tenfold does not “make it alkaline”; pH rises by one unit while the acid stays strong and not too dilute. For a weak acid the link is no longer −log C.

A solution too concentrated for the cuvette is diluted, made up, then read. Beer–Lambert ties absorbance to concentration (A = ε·l·c) while the plot stays linear, often below A ≈ 1. The same dilution factor used above converts the cuvette reading back to the stock. Weigh, make up, measure.

Glossary

Solute
The species being dissolved — salt, acid, sugar, drug. The moles or grams counted in C and Cm belong to it.
Solvent
The medium that takes the solute. Most often water; sometimes ethanol, a buffer, an oil. Solvent does not enter n, but it occupies most of the volume.
Molarity
Molar concentration C = n / V, in mol/L (or mmol/L). Moles of solute per litre of solution, not per litre of solvent poured.
Molality
Moles of solute per kilogram of solvent, in mol/kg. Independent of temperature, and distinct from molarity once the solute weighs or the density leaves 1 g/mL.
Stock solution
The starting, more concentrated solution from which a volume V1 is taken to prepare a more dilute (“daughter”) solution. The bottle on the shelf, the assayed concentrate.
Make up to the mark
Fill a volumetric flask (or deliver from a bulb pipette) until the meniscus is tangent to the single engraved line, at eye level, at the calibration temperature.
ppm
Parts per million. On this page, in dilute aqueous solution, 1 ppm ≈ 1 mg/L, because a litre of water weighs about a kilogram. The equality does not survive a different density (oil, organic solvent, brine).
% w/v
Weight/volume percent: grams of solute per 100 mL of solution. Pharmacy convention. 0.9% w/v saline is 0.9 g of NaCl in 100 mL, i.e. 9 g/L. Neither % w/w nor % v/v.

Related calculators