Tank Fill Time Calculator (Volume & Flow Rate)
The time to fill (or drain) a tank at a constant flow rate follows directly from the volume involved and the flow rate available. Either enter the volume directly, or use a cylindrical tank whose volume is worked out from the diameter and the fluid height to process — the two tabs below.
Calculator
How a fill time is calculated
t = V / Q
Vcylinder = π × (D/2)² × H
At a constant flow rate, the time is simply the volume to process divided by the flow rate. That's an approximation that assumes a steady flow throughout the operation : a positive-displacement pump driven at constant speed comes close to it, while a gravity fill that slows down near the end departs from it more.
A short glossary follows; the asterisk marks the first use only.
Constant vs. variable flow rate: the limits of this approximation
Fill time* on this page is volume* divided by volumetric flow*: t = V / Q. That holds only while Q stays put from the first litre to the last. A positive-displacement pump — vane, piston or screw — on a fixed drive comes close: each revolution shifts a set volume, discharge pressure may rise, and the delivered flow barely moves. A closed-loop flow controller holds the same line.
t = V / Q
A centrifugal pump does not.
The Q–H curve cuts flow as head* rises. An empty tank means low head and a high Q. Near the top the static lift is up, Q may already sit 10 to 30 % under the opening value, and the clock runs on. A pump power calculator fixes one duty point and does not hold it while the level rises.
Mains water, or an overflow that starts to spill, shifts Q the same way. The t = V / Q printed here is a floor time at a flow that was held. Once Q wanders, the figure is a sense of the job, not a handover time.
Gravity drain time: why the flow rate slows near the end (Torricelli's law)
A bottom valve, and no pump. The jet leaves at about the speed Torricelli wrote, v = √(2 g h), with h the liquid height above the orifice. As the tank empties, h falls and the jet dies back.
Flow is not constant.
v = √(2 g h) ; Q = Cd · a · √(2 g h)
The discharge coefficient* Cd is typically 0.60 to 0.65 on a sharp-edged orifice, and a little higher on a rounded nozzle. A 20 mm orifice at Cd = 0.62 and h = 1.50 m gives v ≈ 5.4 m/s and Q ≈ 63 L/min at the start. With 15 cm of liquid left, Q is down to about 20 L/min. The last centimetres take a long time, and longer if the opening starts to gulp air.
For a tank of constant area A, the time to run dry is not V / Qinitial. It is twice that.
t = (A / (Cd a)) · √(2 H / g)
Putting the opening flow into t = V / Q understates the empty time by a factor of two — the usual “open the valve and the tank will empty itself” mistake.
Rectangular or composite-shaped tank: adapting the volume calculation
The cylinder tab uses V = π (D/2)2 H, and H there is the liquid height to be moved, not the shell height. A square tank is L × W × H. A hopper-bottom silo, a horizontal road tanker or a dished-end vessel does not stay linear with H.
- Vertical cylinder or prism — constant section, V = A × H. Known volume after a side calculation, or the cylinder tab.
- Horizontal cylinder — volume against dip is a circular segment. The volume does not follow the dip in step: few litres per centimetre near the bottom and the top, many through the middle.
- Conical or dished bottom — the bottom volume (a cone is π r2 h / 3) is added to the cylindrical part. The first centimetres and the last are not the same number of litres.
A doubtful shape is split into pieces of roughly constant section; the volumes are added and put back into t = V / Q. The form need not draw every shape.
Safety margin to allow on a quoted fill time
A time that lands on the arithmetic to the second almost never occurs. Air sits in the strainer, a valve stops short of fully open, viscosity runs above the nameplate, an operator is on another skid, a float sticks. On a loading bay, 10 to 15 % spare is the least usually allowed. On a sticky fluid, or a pump at the end of its curve, 20 to 30 % is a normal allowance, not an inflated one.
A tight overflow and a quoted time that runs long leave the pump running.
The margin has to match the way the fill stops. A level switch that trips the motor makes the calculated time a planning figure, not a stopwatch held on the button. A stop by hand calls for a long allowance, and for room in the overflow.
A tanker bay, a food batch or a bund is not sized on the raw t from this form. The margin and the freeboard* go into that size. A case in which the pump delivers only 80 % of nameplate flow goes in with them.
Repeated fill/drain cycles: impact on pump sizing
Once a week, 40 min or 55 on a tank fill makes little practical difference. A reactor on sixteen batches a day loses a batch by Friday for every minute added to the fill.
At that duty, t = V / Q is a line-speed number, not a curiosity. The pump sees frequent starts, heat, NPSH on every prime, and seal wear. A pump that is 20 % slow means overtime or a second machine. A pump made large to save three minutes on an hourly cycle costs power, water hammer, and a control loop that hunts. Acceptable cycle time is fixed first; flow is chosen from it, and power from the flow.
This page is the first cut, not the last. It states the duration at a given Q. Whether that Q will stand an eight-hour shift is decided by the process.
Positive-displacement pump flow vs. a tap or valve flow
- Positive-displacement pump — Q ≈ displacement × speed. Tank level hardly matters until the relief valve lifts. t = V / Q belongs to this case.
- Centrifugal pump — Q moves along the curve as soon as H rises. On a fill from the top, H is geometry plus losses plus liquid height. Near the brim the flow sits below the nameplate value.
- Tap, valve or orifice — Q follows √ΔP. ΔP is upstream pressure minus ρgh of the level. Flow falls as the tank fills: Torricelli’s relation again, even when the upstream side is not open air.
Q taken at the start and again at the end can be averaged when the gap stays modest. Above about 20 %, one pass of t = V / Q misstates the duration: integrate along the falling flow, or take the smaller Q and accept a pessimistic time.
Common volume units by industry (food processing, construction, manufacturing)
The litre is a shared name, not a shared unit.
Food and drink are reckoned in litres and, in a brewery or a dairy, in hectolitres (1 hL = 100 L = 0.10 m³). Construction prefers cubic metres, and keeps litres for small mixes. Process plant lives in m³ and m³/h, with L/min on skids and on metering pumps.
Across the Atlantic, or on an old UK site, gallons appear. An imperial gallon is 4.546 L; a US gallon is 3.785 L, and the two stand 17 % apart. A “5,000 gallon tanker” is not the same vehicle in Felixstowe and in Houston. This form works in litres and cubic metres. Gallons are converted before entry, and the gallon that was meant is written down.
Worked example: filling a tanker truck, draining a process vessel
A road tanker with 18 m³ usable, loaded at 350 L/min, needs t = 18,000 / 350 ≈ 51 min. Another 10 % for vents, compartment changes and paperwork puts an hour on the stand. Where the pump is centrifugal and the tanker fills from the bottom, end-of-load flow is under 350 L/min. That hour is not spare capacity.
A process vessel of 2.40 m³, transferred at 120 L/min, needs t = 2,400 / 120 = 20 min. Sixteen batches a day is 5 h 20 of filling.
Another 20 L/min, from a slightly larger line (see pipe flow and diameter), takes 3 min off each batch and nearly an hour off the day. Pipe size is not a footnote.
The same vessel, drained by gravity through a DN25 branch (Cd ≈ 0.62, initial H of 1.80 m, area 1.33 m²), opens at about 109 L/min. The real empty time is nearer 44 min, not 22. Torricelli again.
Working height and freeboard
The “fluid height to process” entry is not the full tank height. Freeboard is the unused band left for expansion, foam, settling, and staying off the weir on the first surge. A common starting point is 5 to 10 % of the height, or 150 to 300 mm on a short vessel. Foaming liquids and violent fills take more.
A vessel is rarely taken bone-dry when the pump must stay primed. The same limit appears when an agitator must not beat air. The volume that counts is the working stroke, from low level to high level, not the geometric volume on the vendor’s drawing.
Pipe diameter sets the clock as well
In a line, Q is velocity times area. At 1.5 m/s — a civil speed for water, not lossy and not noisy — a DN50 of about 50 mm bore carries roughly 10 m³/h. A DN80 carries nearer 25 m³/h.
Q = v × A
Moving 18 m³ in 20 min is 54 m³/h, already past a DN80. The flow–velocity–diameter calculator comes before any choice of pump.
Many jobs blamed on a small pump are an undersized pipe. The machine is driven hard, about 5 % of Q comes back, and the rest is lost to friction.
Level trip, overflow and bund
A fill time is meaningful only when the stop is defined. A float, a conductivity probe, radar, or a hydrostatic switch (see hydrostatic pressure) gives at least one high-level device, better two, with an overflow set above them. The overflow is sized for the pump’s maximum flow, not for the “average” Q on this form.
A bund surrounds the tank. A misread time or a forgotten valve puts cubic metres on the floor. The bund is usually the volume of the largest tank (often 100 %), not twenty minutes of transfer.
A stopwatch has never been a safety instrument.
Glossary: volumetric flow, volume, fill time, freeboard
- Volumetric flow
- Q, volume of liquid per unit time. With Q constant, fill time is V / Q.
- Volume
- V, the liquid to move: typed in, or π (D/2)2 H on the cylinder tab, where H is the height to process.
- Fill time
- t = V / Q for a fill or a drain at that flow. A floor time if Q falls as the level changes.
- Freeboard
- Height left unused above the working level, short of the overflow or the top of the shell.
- Discharge coefficient
- Cd in Q = Cd · a · √(2 g h), the share of the ideal Torricelli jet that leaves the opening.
- Head
- Pump pressure written as a height of liquid. It rises with the level and moves a centrifugal duty along the Q–H curve.