Resistor color code: read the bands or find them (4, 5 or 6)
Small resistors do not carry their value in figures: it is painted on as colored bands, following an international code (IEC 60062). Two or three bands give the significant digits, the next one the multiplier (the number of zeros), the last one the tolerance — and an occasional sixth band, the temperature coefficient.
This page decodes in both directions: pick the colors in front of you to get the value in ohms with its min/max bounds, or start from a value to know which bands to look for in your drawers.
Which way round? The tolerance band (often gold or silver) sits slightly apart from the others: put it on the right. Gold and silver can never be a first band.
Decoding
Glossary: ohm, kilohm, megohm — the unit of resistance and its multiples
Resistance is in ohms (Ω). The prefixes keep the zeros down: 1 kΩ = 1,000 Ω, 1 MΩ = 1,000,000 Ω. Nobody says “four thousand seven hundred ohms” at the bench — it is 4.7 kΩ.
Glossary: tolerance, significant digits, multiplier, temperature coefficient (ppm/°C)
- Tolerance — allowed window around the nominal, ±1 %, ±5 %, ±10 %…
- Significant digits — the first two (4-band) or three (5-band) stripes.
- Multiplier — power of ten after those digits. Gold ×0.1, silver ×0.01.
- Tempco — ppm/°C, the sixth band when it is there. 100 ppm/°C on a 10 kΩ part is 1 Ω per kelvin.
The full IEC 60062 color code table, ready to print
IEC 60062 is the document. Digit, multiplier, tolerance and tempco share the same colours with different jobs depending on which band you are on.
| Color | Digit | Multiplier | Tolerance | ppm/°C |
|---|---|---|---|---|
| Black | 0 | ×1 | — | — |
| Brown | 1 | ×10 | ±1 % | 100 |
| Red | 2 | ×100 | ±2 % | 50 |
| Orange | 3 | ×1 k | — | 15 |
| Yellow | 4 | ×10 k | — | 25 |
| Green | 5 | ×100 k | ±0.5 % | 20 |
| Blue | 6 | ×1 M | ±0.25 % | 10 |
| Violet | 7 | ×10 M | ±0.1 % | 5 |
| Grey | 8 | ×100 M | ±0.05 % | 1 |
| White | 9 | ×1 G | — | — |
| Gold | — | ×0.1 | ±5 % | — |
| Silver | — | ×0.01 | ±10 % | — |
No band, or a wide body mark, is sometimes ±20 %. Rare on anything you would still buy.
Which way to read a resistor: the three clues that never lie
- The tolerance band (gold, silver, or a lone brown on 1 %) sits apart, at one end.
- On 5- and 6-band parts the first stripe is closer to the cap than the last.
- When the body is a mess, measure it. Then turn the code so it agrees.
Reading 4.7 kΩ backwards as 2.4 MΩ is a rite of passage. Once.
4, 5 or 6 bands: what each format means and where you meet it
- 4 bands — two digits, multiplier, tolerance. Carbon and general metal-film, ±5 % / ±10 %.
- 5 bands — three digits, multiplier, tolerance. 1 % and 2 % metal film.
- 6 bands — the fifth plus tempco. Precision and anything that will see a temperature swing on purpose.
Mnemonics for remembering the color order
Black, brown, red, orange, yellow, green, blue, violet, grey, white — 0 through 9. A mnemonic that does not belong in a workshop is not a mnemonic worth keeping. Two that do:
- BBROYGBVGW — just the initials, said as a string. Ugly, memorable, no story.
- Better Be Right Or Your Great Big Venture Goes West — the polite English one.
Gold and silver are not in that ten. They are multipliers and tolerances only.
The E12, E24 and E96 series: why 4.7 kΩ exists and 4.5 kΩ does not
Preferred numbers so that neighbouring values overlap once you include tolerance. E12 (±10 %): 1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8, 8.2. E24 adds 1.1, 1.3, 1.6, 2.0, 2.4, 3.0, 3.6, 4.3, 5.1, 6.2, 7.5, 9.1. E96 is 1 % and includes 4.64 and 4.75, still not 4.50. 4.7 kΩ is the value on every bench because it is E12, not because physics likes 47.
Checking a reading with a multimeter: hooking up, picking the range, interpreting
- COM and the Ω jack. Lift at least one leg if the part is in circuit, or you measure the network.
- Range just above the expected value, or autorange. A 10 kΩ on a 200 Ω range looks like overflow, not a fault.
- Compare with the coded window. 9.8 kΩ on a 10 kΩ ±5 % is healthy. 1.0 kΩ means you read the stripes the wrong way, or you have the wrong part.
Brown or red, orange or red: the frequent color mix-ups and how to settle them
Brown is earthy, red is saturated. Orange has yellow in it. Green is brighter than blue. Old varnish and yellowed bodies erase those distinctions. A daylight lamp helps; a meter settles the argument. The sixth band (often blue = 10 ppm) is a favourite misread on 5-band parts you mistook for 6-band.
SMD resistors: the 3- or 4-digit numeric code and the EIA-96 code
- Three digits — two significant, then the decade. 472 = 47 × 10² = 4.7 kΩ.
- Four digits — three significant, then the decade. 1002 = 100 × 10² = 10 kΩ.
- EIA-96 — two digits from a 96-value table plus a letter multiplier (A = 10⁰, B = 10¹, C = 10²…). 01C is 100 × 100 = 10 kΩ, not “1 C”.
Tiny 0402 parts may have no code at all. Then the reel label is the datasheet.
What tolerance changes in a real circuit: the voltage divider example
Two 10 kΩ in a divider should give Vin/2. With ±5 %, worst case is one high and one low: the ratio walks by about 5 %. On 5.00 V that is a few hundred millivolts — fine for an LED, fatal for an ADC reference. 1 % (or a matched pair) is the usual upgrade, not a bigger calculator.
Vout = Vin · R2 / (R1 + R2)
Step-by-step decoded examples: 220 Ω, 4.7 kΩ, 10 kΩ at 1 %, 1 MΩ
- 220 Ω ±5 % — red, red, brown, gold. 22 × 10 = 220. Window 209–231 Ω.
- 4.7 kΩ ±5 % — yellow, violet, red, gold. 47 × 100 = 4,700.
- 10 kΩ ±1 % — brown, black, black, red, brown. 100 × 100 = 10,000.
- 1 MΩ ±5 % — brown, black, green, gold. 10 × 100,000 = 1,000,000.
Power rating is not in the colour code
Stripes tell you ohms, not watts. Body size does: ¼ W is the common through-hole, ½ W is longer, 1 W is a different animal. A 10 kΩ ¼ W and a 10 kΩ 2 W wear the same bands. Read the length before you drop it into a load.
Zero-ohm jumpers and the single black band
A through-hole jumper is often one fat black band: 0 Ω, a wire with a resistor's face. SMD jumpers are marked 0 or 000. They are not a mysterious code for 1 Ω. Continuity on the meter, and move on.
Carbon film, metal film, wirewound: why the bodies look different
Beige/tan carbon, blue or light-brown metal film, ceramic-white wirewound with a fat body. Carbon is noisier and a looser tempco; metal film is the default 1 % part; wirewound is for power and can be inductive, which is a problem in a snubber or an audio filter. The colour code is the same. The part is not.
Gold as the third stripe on a 4-band part is ×0.1, not “tolerance in the wrong place”. 22 gold gold is 2.2 Ω ±5 %. Swap the two golds in your head and the value jumps a decade.