EN

Calculate How Many Plasterboard Sheets You Need

A plasterboard wall is built on a metal frame — track fixed to the floor and ceiling, with studs or furring channels spaced at a regular centres — then lined with one or two layers of board, with or without insulation between the studs.

Choose the type of job (partition wall, dry lining or suspended ceiling) and enter its dimensions: the calculator returns the number of boards, the length of framing and the accessories (screws, jointing tape, filler, fixings) to allow for.

1.20 m2.40 mstuds every 60 cm30 cm15 cmscrews set back ≈12 mm from the edge…
Sample of 3.5 boards (the real wall continues beyond it) — each dot is a screw.

The job and its dimensions

Partition wall dimensions

Door(s), doorway(s)… 0 if none. A partition wall has two faces: this area is deducted on each.

Boards and frame

Common sizes: 2.4 × 1.2 m (standard, 2.88 m²), 2.7 × 1.2 m, 3.0 × 1.2 m.

Insulation (optional)

Ignored if the box isn't ticked. Insulation area needed = net area of one face.

Accessories (editable assumptions)

Indicative: 15 screws/m² for a board screwed to a metal frame.

Wall plugs driven along the track (floor, ceiling, wall).

Indicative: 0.3 kg/m for the full treatment (tape plus two coats of filler).

Dimensions of the wall to be dry lined

Window(s), door(s)… 0 if none.

Boards and frame

Common sizes: 2.4 × 1.2 m (standard, 2.88 m²), 2.7 × 1.2 m, 3.0 × 1.2 m.

Insulation

Ticked by default: this is by far the most common use of dry lining.

Accessories (editable assumptions)

Indicative: 15 screws/m² for a board screwed to a metal frame.

Wall plugs driven along the track (floor, ceiling, wall).

Indicative: 0.3 kg/m for the full treatment (tape plus two coats of filler).

Room dimensions
Boards and frame

Hangers spaced roughly every 1.2 m along each furring channel — a common trade rule of thumb.

Insulation (optional)
Accessories (editable assumptions)

Indicative: 15 screws/m² for a board screwed to a metal frame.

Wall plugs driven along the track (floor, ceiling, wall).

Indicative: 0.3 kg/m for the full treatment (tape plus two coats of filler).

Trade terms marked with an asterisk are spelled out in the glossary at the end of the article.

9.5, 12.5, 15 or 19 mm: which board thickness for which job

UK merchants sell plasterboard* by millimetres of gypsum between two sheets of paper, not by a French BA code. That number is thickness. Nothing else. Density, glass fibre, water repellence sit in a different letter on the pack.

The sheet everyone means is 12.5 mm, 2400 × 1200 mm, 2.88 m². A plasterer says “a board” and pictures that. Other thicknesses exist. They earn their place. They do not replace wallboard by default.

  • 9.5 mm — the old ceiling board, still used on curves and some lightweight linings. Too whippy for a partition that will take a shoulder.
  • 12.5 mm — partitions, linings, most MF* ceilings. A 2400 × 1200 sheet is a one-person lift if the job is used to it; two people are kinder on a stair.
  • 15 mm — stiffer. Fire or acoustic build-ups, a wall that has to take knocks, sometimes a tiled face when the system sheet says so.
  • 19 mm — plank, or a heavy fire/acoustic leaf. Two people, and a reason on the drawing.

US jobs talk in inches: ½ in is roughly 12.5 mm, ⅝ in roughly 15 mm, on 4 × 8 ft sheets — drywall, in that market, not plasterboard. Same arithmetic in this calculator. Type the actual sheet size. Leave 1.20 × 2.50 m in the fields and the count is for a French pallet, not the van outside.

In practice, 12.5 mm is the starting point. Thickness changes when the system, a fire strategy or a tiler requires it — not because thicker always means better. Two 12.5 mm layers, screws staggered, often outperform a single 15 mm sheet that was hung on a lazy grid.

Standard, moisture-resistant, acoustic and fire-rated plasterboard

Face paper is colour-coded in most British yards. The letters on the pack are more reliable than the tint.

  • Standard wallboard (ivory/grey) — dry rooms. Living room, bedroom, office. Cheapest, and enough where there is no water.
  • Moisture-resistant* (green) — kitchens, bathrooms, a cellar that stays damp. It shrugs off humidity. It is not a tanking* membrane. A shower still needs a proper wet-room system on top.
  • Acoustic (often denser, sometimes blue — SoundBloc and its cousins) — more mass. Helps, especially with mineral wool and a decoupled frame. It will not turn a stud wall into a recording room on its own.
  • Fire-rated (pink, FireLine and equivalents) — glass fibre in the core. The 30- or 60-minute rating belongs to the system — boards, studs, insulation, joints — not to a single sheet bought loose.

Green board in a bathroom is not waterproofing. It copes with moist air. It does not cope with a leaking tray. Tile, tanking, silicone — a different layer, after the board is up.

Mixing types on the same elevation “because three ivory boards were left” shows after the first wet week. A strip of standard above a basin, next to green around the bath, cockles. The joint between them is where the story starts.

Single or twin stud, 400 mm or 600 mm centres

Sound travels through whatever connects the two faces of a partition. One row of C-studs with board both sides is a single frame. Fine as a room divider. With wool in the void the figure typically sits in the high 30s to around 40 dB — conversation drops, a television against the bed-head does not vanish.

A twin frame (two independent rows of studs, wool in both cavities) breaks that metal bridge. Ten decibels more is a realistic order of magnitude, sometimes better. Bedrooms back to back, a home office against a living room. This calculator prices a single frame. Twin means twice the metal, a gap between the rows, and a sketch.

Centres*: 600 mm is the usual British pitch under 12.5 mm wallboard (the sheet is 1200 mm, so joints land on studs). 400 mm stiffens the leaf — ceilings, 9.5 mm, tiling, two layers. For sound, decoupling beats packing extra studs “to make it heavier”. A stiffer leaf can even hit coincidence a little earlier. The system data sheet wins over a rumour on site.

That said, dropping a 4 m partition from 600 mm to 400 mm centres adds two or three studs, not a new acoustic rating. What actually moves the number is the wool, the mass of the boards, and two faces that no longer share the same steel.

Dot-and-dab versus independent metal dry lining

Two ways to dry-line a masonry wall. They are not interchangeable on the same elevation.

Dot-and-dab sticks the board — or a laminated insulated plasterboard — to the wall with adhesive dabs. Thin, quick, fine on a reasonably flat wall. It will not hide a 20 mm bow. No service void. And the neighbour’s noise still has a solid path, because everything is glued to the masonry.

Independent metal lining — floor and head track, C-studs, wool, boards screwed on — costs 80 to 150 mm of room. A straight plane, a void for cables, proper insulation, a bit of acoustic break. Crooked Victorian brick, a rewire, a room that is actually lived in: that one. The “Dry lining” tab on this page is the metal version, not the dabbed one.

Dab when the wall is already true and millimetres are short. Stud when the finish has to look straight, or when the wall is not. Dabbing a rubble wall “to save time”, then packing the hollows, often takes longer than the frame. All the same, dabs have a place: a flat, dry wall in a small room where every centimetre of floor counts, and no pipes to hide.

Staggered joints: why four corners must never meet

Four corners meeting is a cross joint. Board hates it. First bit of floor movement, first wet week of drying out, the crossing opens like a star. It shows after decoration, which is too late.

Offset the vertical joints from one course to the next — 400 mm minimum, half a sheet is better. Joints sit on a stud, never in mid-span. On a ceiling, same rule, and a joint is not lined up with a short run of channel at the edge.

This calculator divides an area. It does not draw the layout. Staggering is a chalk line, before the first screw. Making it up at the last board is how a 100 mm shortfall becomes four corners in the middle of the wall.

Tape and joint in three coats

A bad joint shows more than a crooked cut. In the UK the finish is either tape-and-joint* to a paint surface, or a tape then a full skim. Either way, the joint itself is three operations, not one fat wipe.

  1. Bed the tape — a ribbon of jointing compound in the taper, paper tape (or fibre tape if that is the spec), air chased out from the middle. Leave it to set.
  2. Fill — a wider coat to hide the tape thickness. Set again. Gypsum does not like being buried wet.
  3. Finish and sand — a still wider coat, then 120–180 grit. A blend, not a ridge.

External corners take a metal or PVC bead, bedded in. Without it, the first cupboard scrapes the paper off. Screw heads sit just below the paper — not punched through, not proud. They get the same three coats.

The 0.3 kg/m in the form is a rule of thumb for those three coats. A tape that has bubbled gets done twice, and the bag goes twice as fast. Worth noting: a full skim over the whole wall is no longer 0.3 kg/m. That is a different take-off, in kg/m², and a different bag.

Quilt or slab insulation between the studs

Insulation in the void does two jobs: heat, and a bit of sound (absorption in the cavity, not magic). The R-value* is worked out separately from thickness and lambda — that is the wall thermal resistance calculator. This page counts the square metres that go between the studs.

A glass-wool quilt cuts with a knife, friction-fits with a light squeeze. Cheap, fine in a thermal lining. Too floppy and it slumps in a tall partition, leaving a gap at the head — exactly where noise leaks. A semi-rigid slab, usually rock wool, stands up on its own, cuts with an insulation saw, and soaks up low frequencies better. That is the one for a partition that has to do some acoustic work.

Ramming it in “so it stays” loses thickness, so the R-value drops. Cut it to the centres, butt the edges, board over before the wool drinks site moisture.

The lining tab ticks insulation by default; the partition tab does not. That is deliberate. A simple room divider often goes up empty. An external wall lining almost never does. Even so, an empty partition between two bedrooms is a drum. A 50 mm slab in a 70 mm stud already changes the room, without pretending to be a studio.

Extra framing at a door or a ceiling hatch

The calculator drops a stud every 600 mm, plus one at each end. A door wants more: double studs (or a stud and a jack) each side, the head track cut, a lintel section screwed between. The lining fixes into that steel, not into the gypsum.

In an MF ceiling, a hatch, a fan, a heavy downlighter gets a framed opening in channel, with extra hangers if the hole is wide. Board edges sit on a section, not in mid-air.

Those extra lengths are not in the automatic take-off. They go on the list. Leave them off and the first slam stars the joint at the jamb, and the lining has nothing to bite.

Worked example: a 4 × 2.4 m partition with a 1.8 m² door

Partition, 12.5 mm board 1200 × 2400 mm (the UK sheet), one layer each side, 600 mm centres, 5% waste — form defaults, height matching a British storey. Door 900 × 2000 mm, 1.80 m².

  1. Gross area — 4.00 × 2.40 = 9.60 m².
  2. Net area, one face — 9.60 − 1.80 = 7.80 m².
  3. Both faces — 7.80 × 2 = 15.60 m² of board.
  4. Raw count — 15.60 / 2.88 ≈ 5.42 sheets.
  5. With 5% — 5.42 × 1.05 ≈ 5.69, rounded up to 6 sheets.

(7.80 × 2) / (1.20 × 2.40) × 1.05 → 6 boards

The frame ignores the door hole: 2 × 4.00 = 8.00 m of track, and ceil(4.00 / 0.60) + 1 = 8 studs, 19.2 m of stud. Frame total 27.2 m. Joints, laid out on the full 4 m run (4 boards wide, 1 course high, two faces), come to 14.4 m — about 15.1 m of tape with the overlap, 4.3 kg of compound at 0.3 kg/m. Screws at 15/m²: 234.

Six sheets is tight once the reveals are cut. Bump the waste to 10% and a seventh is bought, which is more honest around an opening. The extra jack studs at the door still sit on top of the 8. In short, the sheet count is not the whole list: jacks, a lintel, often a 3 m track cut in two.

Tapered edge, square edge, skim

Most wallboard is tapered edge (TE) on the long sides: that shallow dish is where the tape lives, so the joint can finish flat. Square edge (SE) is for a full skim, or for edges that will take a bead. Tape-and-joint on square edge leaves a ridge that glancing light finds in a minute.

A plasterer skimming the whole wall still wants the joints taped first, or the joints telegraph. This page’s filler quantity assumes tape-and-joint, three coats, not a 2 mm skim over the lot. If the finish is a skim, the bag count is a different take-off.

Rather than buying SE “because it was cheaper on the pallet”, match the edge to the finish. TE for a painted tape-and-joint wall. SE under a skim. Mix them on one elevation and the ridge writes itself.

2400, 2700, 3000 mm sheets

2400 × 1200 is the sheet on every white van. It lands under a 2.4 m ceiling… except for the head track, the floor track, and a bit of clearance. So it is cut. 2700 and 3000 mm boards exist so a storey-height wall is one piece, no horizontal joint, no noggin to carry that joint.

A horizontal joint is another course in the layout, more tape, and usually a section of track to support the edge. If the room is 2.45 m to the soffit, a 2400 board forces that joint. A 2700 does not. The board-height field is there for that — not to leave 2.50 m in because a French default says so.

A 3000 mm board in a 2.48 m room is cut, and the 520 mm offcut will start a reveal or a bulkhead — provided it was planned before six 2400 mm sheets went on the ticket.

MF ceilings: channel and hangers

The ceiling tab does not plant studs. It plants a perimeter channel (round the room), furring channels one way, and hangers up to the soffit. Hanger spacing along a channel is taken here as 1.20 m, a fixed site figure. Channel centres are set in the form (400 mm is common on ceilings, sometimes 450 or 600).

Ceilings are often fixed at tighter centres than partitions, and 9.5 mm wants a manufacturer’s say-so. Downlights, an extract fan, anything with weight: frame it. Do not notch a channel on a whim. There is no opening-area field on this tab — a ceiling has no door. Hatches are deducted by hand, and the hole is steeled.

A 4 × 3 m ceiling is not “12 m² of board and a bit of channel”. It is the perimeter (14 m), the furring, hangers every 1.20 m, often a quilt laid over the back. The form adds them. The sketch decides the run — towards the light, or towards the shorter span.

After the boards: paint and floor

A partition is not finished until the joints are hard, sanded and dusted off. Primer and coats are a separate take-off: the paint quantity calculator takes over. Paint too soon, with the tape still green, and every joint prints in raking light. Wait until the next day — sometimes the day after, if the room is cold — and the primer seals the paper without cockling it.

The floor waits until the partitions are up and the skirtings are still off. Boards or laminate are ordered in packs, with a cutting allowance, not in plasterboard sheets. Lay the floor before the plasterboard and it is dusted, smeared with compound, and pinched under track. The usual order is one sentence: frame, insulation, boards, joints, paint, floor, skirting.

An external lining, though, does not wait for paint before it takes its wool. The quilt goes in before the board. Paint insulates nothing.

Glossary

Plasterboard
Gypsum core between two sheets of paper. The British trade word; the same product is drywall in North America. Thickness (9.5, 12.5, 15, 19 mm) is not the same as type (standard, moisture-resistant, fire, acoustic).
Moisture-resistant
Board with a treated core and, usually, green face paper. It copes with humid air in kitchens and bathrooms. It is not waterproof, and it does not replace tanking under tiles.
Tanking
Waterproof membrane or coating applied on the board, under tiles, in a wet room or around a shower. Green board alone is not tanking.
Centres
Distance from the centreline of one stud (or channel, or hanger) to the next. 600 mm is the usual pitch under a 1200 mm board; 400 mm stiffens the leaf.
Tape and joint
Finish in which paper (or fibre) tape is bedded in jointing compound over the tapered edges, then filled and sanded, ready for paint. Distinct from a full plaster skim over the whole wall.
R-value
Thermal resistance of a layer or a wall, in m²·K/W. Higher R means less heat flow. It depends on thickness and conductivity (lambda), not on the number of boards.
MF
Metal furring. A suspended ceiling of perimeter channel, furring channel and hangers, with plasterboard screwed underneath. Not a partition stud wall hung upside down.

Related calculators