EN

Voltage divider: work out Vout or find R1 and R2

The voltage divider is the simplest circuit in electronics: two resistors in series are enough to step a voltage down in a fixed proportion — reading a 5 V sensor on a 3.3 V input, scaling a signal, biasing a transistor. The output is taken between the two resistors: Vout = Vin · R2 / (R1 + R2).

The calculator gives Vout, the current drawn around the clock, the power in each resistor and the output impedance — and, if you enter the load connected behind it, the voltage you actually get. In reverse, it finds R1 for a target Vout, nearest E24 value included.

A voltage divider only suits a signal or a very light load: it is not a power supply. As soon as the load draws a current comparable to the divider's own, the voltage collapses — the usual rule wants the load at least 10 times more resistive than the divider's output impedance.

The divider

Direction

Switch direction then run the calculation again to adapt the fields.

R1 (Vin side) and R2 (ground side)

Vout is measured across R2.

Optional: shows how much the voltage sags under load.

Glossary: voltage, current, resistance, ground — the basics without jargon

Voltage is the pressure, in volts. Current is the flow, in amperes. Resistance is the squeeze, in ohms. Ground is the 0 V you measure against — the negative of a single supply, not a mystical earth stake. Two resistors in series between Vin and ground, tap in the middle: that tap is Vout.

Glossary: output impedance, load, "unloaded", resistors in parallel (the ∥ symbol)

  • Unloaded — nothing drawing current from the tap. The school formula is then exact.
  • Load — whatever you hang on Vout (ADC, LED, next stage). It sits in parallel with R2.
  • Output impedance — what the load “sees”: R1 ∥ R2, looking back with Vin shorted (Thevenin).

R1 ∥ R2 = R1 · R2 / (R1 + R2)

Where the formula comes from: Ohm's law applied twice, step by step

Same current through both resistors. I = Vin / (R1 + R2). Drop on R2: Vout = I · R2.

Vout = Vin · R2 / (R1 + R2)

Solve the other way if you already own one resistor:

R2 = R1 · Vout / (Vin − Vout)   ·   R1 = R2 · (Vin − Vout) / Vout

The current divider is the parallel twin of this: other resistor on top, I instead of V. Do not mix the two lines.

Choosing the order of magnitude of R1 + R2: consumption versus noise sensitivity

Small sum (a few kΩ): stiffer tap, more idle current. Large sum (hundreds of kΩ, megaohms): kind to a battery, easy prey for pickup and for the nanoamps of an ADC pin. 10–100 kΩ total is the boring, good band for a 5 V or 3.3 V rail.

The 10× rule explained: why the load squashes the voltage

Rload across R2 pulls the tap down. If the divider's idle current is ≥ 10× the load current, the sag stays under ~10 %. Equivalently:

R1 + R2 ≤ Rload / 10    (rule of thumb)

An ADC pin is often megaohms DC, so the rule is easy. An LED is not. If you cannot satisfy 10×, buffer or pick smaller resistors and pay the current.

Textbook case: reading a 5 V sensor on a 3.3 V microcontroller (recommended values)

Want 3.3 / 5 = 0.66. R1 = 10 kΩ, R2 = 20 kΩ → 3.33 V. Or 4.7 kΩ and 9.1 kΩ for a closer 3.30 V on E24. The GPIO / ADC leakage is tiny next to 150–300 µA through the divider. Check the pin's maximum voltage: 3.33 V on a 3.6 V-abs-max part is comfortable; 3.6 V from a 5.5 V sensor on a 3.3 V-only pin is a clamp-diode conversation (below).

Why a voltage divider is NOT a power supply — and what to use instead

Draw milliamps and Vout collapses. A divider does not regulate. Power a 3.3 V board from 5 V with an LDO (1117-3.3 and friends) or a buck. The divider is for sensing, biasing, and levels that barely sip current.

The effect of tolerances: how much Vout shifts with 5 % or 1 % resistors

5 V → 3.3 V, both ±5 %, worst case (R1 high, R2 low): about 3.2 V. The other way: ~3.4 V, which may already push past a tight 3.3 V budget. ±1 % cuts that window by five. Matched thin-film is how instrument makers sleep.

The potentiometer: an adjustable voltage divider

A pot is a divider: end to Vin, other end to ground, wiper is Vout. Volume controls, setpoint knobs, panel meters. The track is R1+R2; the wiper splits it. Load the wiper and you still have the 10× problem, now with a position-dependent Thevenin.

Divider for battery monitoring: keeping the permanent drain low

A 12 V pack on a 3.3 V ADC: R1 = 1 MΩ, R2 = 330 kΩ → ~2.98 V at 12 V, ~9 µA drain. Still too much for a coin cell that must sit for a year — then put a MOSFET in the top leg and only power the divider when you sample.

R1 = 1 MΩ, R2 = 330 kΩ  →  Vout = 12 × 330 / 1330 ≈ 2.98 V

Dividers with AC signals: what changes (impedances, compensation capacitor)

Same ratio, impedances instead of R if you mix C or L. A scope probe is a compensated divider: a small cap across the tip resistor, trimmed so the ratio holds from DC to megahertz. On a board, the ADC's few picofarads plus R1∥R2 is a low-pass. A few tens of pF across R2 restores the high end if the signal is fast.

Steadying the output: decoupling capacitor, op-amp follower

10–100 nF from Vout to ground feeds the ADC's sample capacitor and eats hash. An op-amp follower after the tap gives you a stiff Vout without shrinking R1+R2. That is the clean way to drive a changing load from a high-Z divider.

Worked examples: 12 V → 5 V, 9 V → 3.3 V, voltage probe for an ADC

  1. 12 V → 5 V (ADC, not a 5 V rail). R1 = 10 kΩ, R2 = 7.15 kΩ (E96) → 5.00 V, ~700 µA.
  2. 9 V → 3.3 V. R1 = 100 kΩ, R2 = 56 kΩ → ~3.23 V, ~58 µA. Close enough for a battery gauge; scale in firmware.
  3. 0–30 V probe, 0–3.3 V ADC. R1 = 100 kΩ, R2 = 12.4 kΩ → 3.31 V at 30 V, ~267 µA. 10 nF across R2. Mind the voltage rating on R1.

Thevenin of the divider: Rth = R1 ∥ R2

Replace Vin with a short (AC) or a stiff source (DC) and the tap looks like Vth = Vout,unloaded in series with R1∥R2. That Rth is what the ADC acquisition time has to charge through, and what a following RC uses as its R. Write it down; it is the missing number on a lot of “slow ADC” forum posts.

ADC pin current and the sample capacitor

SAR ADCs gulp a few pF at the start of each conversion. Rth × C_sample must settle within the acquisition window. 100 kΩ Thevenin and 10 pF is 1 µs; many chips want a fraction of that. Either lower the resistors, add the reservoir cap at the pin, or enable a longer sample time in the ADC setup. The DC leakage of the pin is a second, slower error on megaohm dividers.

5 V into a 3.3 V pin: the clamp-diode trap

If Vin can rise (sensor unpowered on 5.5 V, or 12 V on a “12 V” battery at 14.4), Vout can exceed the microcontroller's abs. max. Internal clamp diodes then conduct through R1 and the pin, which is a reliability lottery. Size the divider so the highest Vin still lands below the pin max, or add an external clamp / series resistor the datasheet allows. 3.33 V typical is not the same as 3.33 V worst-case.

A divider is a sensor, not a regulator. Loading it like a power rail, or feeding a 3.3 V pin from a 5 V source without checking the high end of Vin, are the two ways this circuit bites.

Related calculators