EN

Optical Power & Dioptre Calculator

Optical power (or vergence) measures how strongly a lens converges light. It is the reciprocal of the focal length: P = 1/f, expressed in dioptres (δ) when f is in metres. Convert focal length and dioptres both ways, or add up several lenses in contact just like an optician.

One dioptre = a lens with a 1-metre focal length. The larger the number, the “stronger” the lens (the shorter the focal length). A positive power converges (a magnifier, a long-sight correction); a negative one diverges (a short-sight correction).

Inputs

Mode and unit

Switch mode, then run the calculation again to update the fields.

Focal length → power

Negative for a diverging lens.

Result

  • Optical power P 2.000 δ
Focal length f 50.00 cm (0.5000 m)
Optical power P = 1/f 2.000 δ (dioptres)
Lens type Converging (P > 0) — corrects long-sight / presbyopia

P = 1 / f (f in metres, P in dioptres)

Optical power: rating the strength of a lens

One dioptre is not a brand. It is the thin-lens power of a bit of glass whose focal length is exactly one metre. Opticians live in that unit because two lenses pressed together just add. Combining focal lengths means taking reciprocals first, and nobody does that in a trial frame.

P = 1 / f · Ptotal = P₁ + P₂ + … (thin lenses in contact)

f has to be in metres or you are not in dioptres (δ, D, dpt). A 50 cm lens is 0.50 m, so P = 2 δ. A 25 cm lens is 4 δ. Twice the power, half the focal length. Stack +2 δ and −0.50 δ and you hold +1.50 δ — f = 1/1.50 ≈ 0.67 m. That is the whole arithmetic of a trial case.

The sign is the type. P > 0 converges (a magnifier, a long-sight correction). P < 0 diverges (short-sight). P = 0 is a plane-parallel plate: infinite focal length, no focusing at all.

Correcting eyesight

The eye is already a lens — cornea plus crystalline — that ought to drop a sharp image on the retina. When it misses, you add a spectacle or a contact so the combination lands where it should. The extra glass is a couple of dioptres in front of a system that already runs near 60 δ. Small number, large difference.

  • Short-sight (myopia) — too much converging power, image in front of the retina. A diverging lens, negative power, pushes the image back. Typical Rx: −2.50 δ.
  • Long-sight (hyperopia) — not enough converging power; the image would form behind the retina. A converging lens, positive power, supplies what is missing. Typical Rx: +1.75 δ.
  • Presbyopia — the crystalline stiffens with age and near focus fades. Reading adds or progressives put a few extra dioptres on the lower part of the lens, for 40 cm, not for the horizon.

Astigmatism is a power that changes with meridian. It is written as a cylinder (CYL) plus an axis, on top of the sphere. This calculator treats a single power — one meridian, or the spherical equivalent if you have already averaged.

Why dioptres add when lenses touch

For thin lenses in contact, the air gap is zero. Stack the thin-lens equation twice and it collapses to 1/f = 1/f₁ + 1/f₂, which is P = P₁ + P₂. That is why a practitioner can build a correction from stock lenses without redrawing every ray.

The additivity is a contact rule, not a universal one. Leave a gap e (in metres) and Gullstrand takes over:

P = P₁ + P₂ − e · P₁ · P₂

The extra term is a shrug at a millimetre and a nuisance at a centimetre. This page sets e = 0. For a telescope objective and eyepiece, do not add the dioptres and call it a day.

Focal length has to be in metres

P = 1/f is not “one over whatever you measured”. A 50 mm camera lens is 0.050 m, so 20 dioptres — a strong optic, which is why a 50 mm at f/1.8 is a chunk of glass. Type 50 in the millimetre box and the calculator converts. Type 50 and think metres, and you have invented a 0.02 δ window pane.

Sign follows the thin-lens convention used here: f > 0 (and P > 0) converges, f < 0 diverges. A minus on a prescription is a diverging lens, not a typing error.

Reading the SPH line on a prescription

The sphere (SPH) is this power, in dioptres, almost always to a quarter-dioptre step (0.25 δ). Right eye OD or RE, left eye OS or LE. The plus is written; the minus is written too — do not drop it. CYL and AXIS, if present, sit on top for astigmatism. ADD is the extra plus for near, in the same units.

A “−3.00 DS” lens (dioptres sphere, no cylinder) has f = −1/3.00 ≈ −0.333 m, about −33 cm. That is a moderately strong short-sight correction, not a camera focal length. The two trades share the word “focus” and almost nothing else.

Spectacles, contact lenses, and the vertex distance

A contact lens sits on the cornea. A spectacle lens sits about 12 to 14 mm in front of it. That air is a Gullstrand e, so the power that actually reaches the eye is not the number engraved on the glass.

For low powers you can ignore it. Past about ±4 δ, the optometrist converts: a high minus spectacle becomes a weaker contact, a high plus goes the other way. This calculator does not apply that step. If you are turning a glasses Rx into a contact-lens Rx, the millimetres of air still have to be handled on the side — see below.

When the power cancels

P = 0 means an infinite focal length: a plane-parallel plate, or two lenses that cancel (+2 and −2 in contact). That combination is afocal. Light goes through without being focused. A window, basically.

A Galilean telescope with the image at infinity is afocal as a system, even though each element has a power of its own. They are not in contact, so Gullstrand — or the telescope formula — is the right tool, not a raw sum. In the form, a third power of 0 just means “no third lens”. A sum that lands on zero is a result, not a blank.

Vertex distance: glasses versus contact lenses

British practices usually take a back vertex distance (BVD) of 12 mm, sometimes 13 or 14 if the frame sits further out. The conversion from spectacle plane to corneal plane is

Pcontact = Pspec / (1 − d · Pspec)    (d in metres)

Worked: Pspec = −6.00 D, d = 0.012 m. Denominator 1 + 0.072 = 1.072, so Pcontact ≈ −5.60 D, rounded to −5.50 or −5.75 on a 0.25 D step. The contact is less minus than the glasses. Flip the sign for a high plus: +8.00 at 12 mm becomes about +8.85 at the cornea — more plus, not less.

Under ±4 D the shift is usually smaller than a quarter-dioptre and many people wear the same number in both. Above that, copying the glasses Rx onto a contact blister is the classic mistake. This page stays at e = 0; the formula above is the extra millimetres-of-air step.

Reading an NHS-style spectacle prescription

After an NHS sight test the printout (practice letterhead, sometimes still a GOS-style layout) is almost always the same grid. Right and left. Sph, Cyl, Axis. Add. Prism and base if needed. BVD if the sphere is high.

  • R / L (or RE / LE, OD / OS) — each eye has its own line. Never swap them.
  • Sph — the P of this page. Always with a sign. “DS” means dioptres sphere: no cylinder on that eye.
  • Cyl × Axis — astigmatism, written as a second power at an angle. A typical line looks like R −2.50 / −0.75 × 180.
  • Add — near addition, always plus. Distance vision is Sph alone; near vision is Sph + Add. An Add of +2.00 on a −1.50 sphere gives −1.50 in the distance and +0.50 for reading.

A balance lens (“Bal”) is a dummy for an eye that is not being corrected; it is not a measured power. Intermediate Adds, if present, sit between distance and near. None of that is a third thin lens in the contact sense — it is the same glass, zoned. Use the association mode to add Sph and Add if you want the near power; leave Cyl out of that sum.

Dioptres add exactly only for thin lenses in contact. A gap e needs Gullstrand: P = P₁ + P₂ − e·P₁·P₂ (e in metres). Vertex distance between a spectacle and the eye is the everyday case of a non-zero e. This calculator is the e = 0 case, and it does not apply a BVD correction.

Related calculators