Calculate the Volume and Surface Area of a Cone
A right cone — a circular base with an apex directly above its center — is determined by the radius of the base and the height. The slant height (the length of the sloped edge) follows from the Pythagorean theorem, no need to measure it separately.
Enter the radius and height: the calculator gives the volume, the slant height, the lateral surface area and the total surface area.
Radius and Height
Asterisks lead to the glossary at the end of the article.
One-third of the wrapping cylinder, not a rule of thumb
Same disc, same height, the cone fills exactly one-third of the cylinder that wraps it. Not an estimate. Exact.
Slice the cone into thin discs whose radius grows linearly up to r. Disc area goes as radius squared, hence as the square of the height coordinate, and the integral of x² from 0 to 1 is 1/3. Democritus, Eudoxus, Archimedes — old news. Cavalieri’s principle* is the version that avoids naming the integral: matching heights, cross-sections in a fixed ratio, volumes in that same ratio. A square pyramid tells the same story with a polygonal base. A cone is the round pyramid. Height here is the perpendicular drop from the apex* to the plane of the base, not a sloping edge.
Drop the 1/3 and the result is a cylinder, three times too large. Keep it, and a funnel that “looks about as big as the tin it sits in” is already known to hold far less. That is the whole of the volume formula. Surface is a different length, and a different story.
Slant height from Pythagoras, then the sector that becomes the mantle
The slant height* ℓ — also called the generatrix — is the sloping edge from the rim of the base up to the apex. Vertical height h drops perpendicularly onto the centre of the disc. Pythagoras ties the three together:
ℓ = √(r² + h²)
Cut the cone’s mantle and press it flat. The result is a circular sector of radius ℓ. The arc of that sector is the base circumference, 2πr. A sector’s area is the matching fraction of πℓ², the same fraction as 2πr over 2πℓ, so r/ℓ. What remains is πℓ² × (r/ℓ) = πrℓ. That is the lateral area. Add the base disc πr² for the total.
Slat = π r ℓ ; Stot = π r (r + ℓ)
Central angle of the sector, in radians: 2π r / ℓ. A party hat, a wafer cone, a sheet-metal traffic cone: the pattern starts from this sector. The circle of radius r is the base; the circle of radius ℓ is the disc the sector was cut from. Two different circles. Mixing them is how a hat comes out too small.
Full cone versus frustum: buckets, hoppers, lampshades
Slice the cone with a plane parallel to the base and throw the small tip away. What remains is a frustum*: two discs, radii R and r, and a height H between them. No apex, so no lone “(1/3) π r² h”.
Vfrustum = (π H / 3) (R² + R r + r²)
ℓ = √(H² + (R − r)²) ; Slat = π (R + r) ℓ
Set r = 0 and the full cone returns. Set R = r and a cylinder returns (V = π R² H, as it should). A bucket, a lampshade, a plant pot, a hopper: more often a frustum than a pointed cone. This calculator does not do the frustum. The workaround is large cone minus similar small cone, after recovering the missing tip height by similarity: htip / r = (htip + H) / R.
Without that similarity — a cut that is not parallel to the base — the model breaks. A lop-sided wedge is not a solid of revolution. The R² + Rr + r² term is doing real work: averaging the two bases as if this were a prism would miss the fact that area shrinks with the square of the scale. The geometric mean Rr sits in the middle for that reason.
Right cone versus a slumped heap
A right circular cone* has its apex vertically above the centre of the base. Every generatrix has the same length ℓ. Those are the formulae on this page. An oblique cone has the apex offset. Volume, slightly annoyingly, is still (1/3) × base × perpendicular height — Cavalieri again. Lateral area is not. There is no regular sector and no single ℓ, because there is no single generatrix.
A heap of sand slumped against a wall is not a right cone, even if it “looks conical”. The angle of repose may be constant, but the footprint is a half-disc or worse, and the apex is not above a centre. A traffic cone that has been kicked is closer to oblique than the formula assumes.
This page is a right circular cone. An oblique cone with the same base and the same perpendicular height: same V. Surface, slant height, net: no. ℓ = √(r² + h²) does not belong on a shifted apex.
Inverting volume for a missing radius or height
One unknown, volume known, the other dimension known.
h = 3V / (π r²) ; r = √(3V / (π h))
The 3 is the third. Drop it and a cylinder has been sized by mistake. A 2 L funnel (0.002 m³) with a 10 cm opening radius: h = 3 × 0.002 / (π × 0.10²) ≈ 0.191 m, about twenty centimetres. A traffic cone 50 cm tall whose envelope is 3.5 L: r = √(3 × 0.0035 / (π × 0.50)) ≈ 0.082 m. That looks like a site cone. Volume on its own still leaves infinitely many pairs (r, h). A squat cone and a needle can hold the same amount. The space they take, and the wafer area, do not.
Surface does not invert as cleanly. ℓ depends on both r and h, so a single total area does not pin down the pair. The calculator runs forwards from r and h. A scrap of paper runs backwards from V.
Funnels, traffic cones, silo roofs
A kitchen funnel is often a frustum plus a short tube, not a pointed cone. Useful volume is what can be poured before it spills, not the volume of the solid. A cement silo with a conical roof: cylinder for the barrel, cone for the cap, two calculations, two pages. Party hat, ice-cream wafer, traffic cone, sand heap, pepper pile, model-aircraft nose: once the solid rises to a point from a circle, the envelope volume is this one.
Sheet metal, card, wafer — that is the lateral area πrℓ, not the total. There is no base, or the base is the ice cream. A loose heap is a cone only if the slope is the angle of repose and the footprint is roughly round. Against a wall, as above, it is something else. Nearby in the same geometry section: the cylinder for the wrapping drum, the cuboid for a rectangular hopper, the sphere for a vessel with no axis.
Worked case: radius 4, height 9
r = 4, h = 9, same unit. Metres, for a readable picture.
ℓ = √(16 + 81) = √97 ≈ 9.849 m
V = (1/3) π × 16 × 9 = 48π ≈ 150.8 m³
Slat = π × 4 × √97 ≈ 123.8 m²
Stot = π × 4 × (4 + √97) ≈ 174.0 m²
The wrapping cylinder: 144π ≈ 452.4 m³. 150.8 × 3 = 452.4. The third is sitting there. Slant height 9.85 is only a shade longer than height 9, because the cone is already quite tall (h > r). Flatten it, and ℓ closes in on the radius. In centimetres, V ≈ 150.8 cm³, a small cup. The unit again.
Mixing slant height into the volume formula
The usual slip. The sloping edge can be reached with a tape, so ℓ is measured and typed into h. h is inside, centre of the base to the apex, perpendicular. ℓ lives on the mantle. V = (1/3) π r² h wants h, not ℓ. Slat = π r ℓ wants ℓ, not h.
If only ℓ and r are to hand, recover h = √(ℓ² − r²) — provided ℓ > r, otherwise the triangle does not exist (the cone is too open for that generatrix). This calculator asks for r and h, and works ℓ out. The right pair has to go in. A 3-4-5 cone (r = 3, h = 4, ℓ = 5) makes the distinction loud: volume uses 4, lateral area uses 5. Swap them and both results are wrong, in opposite directions.
Cubic metres, litres, and an ice-cream wafer
1 m³ = 1,000 L, 1 L = 1,000 cm³. A wafer cone, 5 cm radius and 12 cm high: V = (1/3) π × 5² × 12 = 100π ≈ 314 cm³, about 0.31 L. A generous ice cream, or a modest funnel. The 4-by-9 cone in metres is 150,800 L — a tank, not a pudding.
Same habit as the cylinder: everything into metres, read m³, then × 1,000. Or everything in centimetres, then ÷ 1,000 for litres. The 1/3 can sit before or after the product; applying it twice is the remaining way to lose a factor of nine. That said, a result that looks like a swimming pool when a wafer was expected is almost always a unit, not a missing third.
From a sector of a disc to a paper hat
The net is the practical object. Card, tinplate, a party hat: cut a sector of radius ℓ whose arc equals 2πr, join the two radii, and the cone stands up. Arc too short, and the hat is steeper than intended (smaller r, larger h for the same ℓ). Arc too long, and it will not close without overlapping, or it sits too flat.
The opening angle in degrees is (r/ℓ) × 360°. For the worked cone, r/ℓ ≈ 4/9.85 ≈ 0.406, so about 146°. Half a disc would be 180°, a flatter cone. A quarter-disc, 90°, is already a fairly sharp spike. The sector calculator next door will size the piece of card; this page sizes the solid that the card becomes.
Glossary
- Cavalieri’s principle
- Solids of equal height whose cross-sections parallel to the base have equal area have equal volume. It is why a cone is one-third of the wrapping cylinder, even when the apex is shifted sideways.
- Apex
- The tip of the cone. Height h is the perpendicular from this point to the plane of the base, not the length of a sloping edge.
- Slant height
- The generatrix ℓ: the straight-line distance from a point on the base circumference to the apex. ℓ = √(r² + h²) on a right circular cone. Lateral area uses ℓ; volume uses h.
- Frustum
- A truncated cone: the solid left after a cut parallel to the base removes the tip. Two circular faces, no apex. Volume (πH/3)(R² + Rr + r²), not (1/3)πr²h.
- Right circular cone
- A cone whose apex sits vertically above the centre of a circular base. Every generatrix has the same length. The formulae on this page assume that case.