EN

Calculate Magnification with Newton's Lens Equation

Newton's lens equation is another way of writing the thin-lens conjugate relation: instead of measuring the object and image distances from the optical centre (as on the thin lens page), it measures them from the focal points F and F'. That is the natural frame for composite optical systems (camera lenses, telescopes), where the optical centre is not always the handiest reference point.

x is the distance from the front focal point F to the object, x' the distance from the back focal point F' to the image. The relation becomes very simple: x·x' = f², and the magnification reads off directly, γ = −f/x = −x'/f.

OFF'xx'objectimage

Inputs

Mode and unit

Switch mode, then run the calculation again to update the fields.

Find x' (given f and x)

Positive for a converging lens, negative for a diverging one.

Positive if the object is beyond F (the usual case, real image), negative if it sits between the lens and F (the magnifying-glass case).

Result

  • Position x' (from F') 20.00 cm
Focal length f 10.00 cm
Position x (object from F) 5.00 cm
Position x' (image from F') 20.00 cm
Magnification γ = −f/x -2.000
Equivalent dₒ (from the optical centre O) 15.00 cm
Equivalent dᵢ (from the optical centre O) 30.00 cm

x·x' = f² → x' = f² / x · γ = −f/x

Extra-focal stubs whose product is f²

Mark F and F' on a rail and the leftover pieces are what you actually measure: the stub from F back to the object, the stub from F' on to the image. Newton noticed those two lengths are not independent. Their product stays put.

Call them x and x'. Under the same real-is-positive convention as the thin lens page, they are just the Gaussian distances with the focal length peeled off:

x = dₒ − f · x' = dᵢ − f · x · x' = f²

The Gaussian formula still sits underneath. From 1/f = 1/dₒ + 1/dᵢ you get dᵢ = f dₒ / (dₒ − f). Subtract f and the remainder collapses: x' = f² / (dₒ − f) = f² / x. That is the whole derivation. No new physics — a shift of origin, from the optical centre onto the two focal points.

A 50 mm lens with the object 25 mm beyond F gives x = 25 mm, so x' = 2500 / 25 = 100 mm. The image sits 100 mm past F'. Check: 25 × 100 = 50². The arithmetic is the experiment.

Why measure from the focal points, not the optical centre

A single thin element has a centre you can put a caliper on. A camera lens does not. Neither does a telescope objective, a microscope tube, a cemented doublet. The “optical centre” is a construction point, often buried in glass, sometimes floating in air ahead of the front element.

The focal points are the ones you can find. A distant tree, a collimator, a star: F' shows up as a sharp image. Flip the barrel, F shows up. Those two pins are the natural origins of a compound system. Newton's form takes them at face value instead of reconstructing a fictitious O at every stage.

Keep the Gaussian form for a lone thin lens on a bench. Switch to x and x' the moment the centre is no longer a measuring point.

Reading the sign of x and x'

Same sign rule as dₒ and dᵢ: real is positive. x tells you which side of F the object sits on.

  • x > 0 — object beyond F (extra-focal). The everyday case: a real image, catchable on a screen. Because f² is positive, x' comes out positive as well. Same sign, always, for a real focal length.
  • x < 0 — object between the lens and F (intra-focal). That is a magnifying glass: virtual, upright, enlarged. x' goes negative, so the image is no longer “past F'” — it has ducked back the other way.
  • x = 0 — object sitting on F. The image walks off to infinity. The calculator refuses to divide by zero, and that refusal is the physics, not a bug.

A diverging lens (f < 0) does not break the definitions. x = dₒ − f is then a sum, not a difference, and F, F' have swapped their usual sides. The product x x' = f² still holds; f² does not care about the sign of f.

Magnification without going back to dₒ

Lateral magnification is still size ratio plus orientation. Newton hands it to you from the focal stubs alone:

γ = −f / x = −x' / f = −dᵢ / dₒ

Three wrappers, one fact. −dᵢ/dₒ is the optical-centre version. −f/x is the extra-focal version: park the object close to F (small x) and |γ| blows up. −x'/f is the same sentence read from the image end.

Numbers: f = 50 mm, x = 25 mm → γ = −50/25 = −2. Real, inverted, twice as tall — a projector. Flip the stub: x = −25 mm (object 25 mm short of F) → γ = +2. Virtual, upright, still twice as tall — a reading glass. The minus in the formula is doing a job. Same sign of x and f, and the image flips.

Switching between the two formalisms

The bridge is just the definitions, turned around:

dₒ = x + f · dᵢ = x' + f · x = dₒ − f · x' = dᵢ − f

The results table already prints both, so you are not left with two vocabularies and no doorway. f = 50 mm, x = 25 mm, x' = 100 mm is dₒ = 75 mm, dᵢ = 150 mm. Gaussian check: 1/50 = 1/75 + 1/150, and γ = −150/75 = −2. If a problem states dₒ, subtract f, compute, add f back. One subtraction, one addition. Not a change of theory.

Units still have to match. A 50 mm focal length and a 2.5 cm extra-focal stub are the same length written twice — or a factor-of-ten wreck, if you forget.

The two limits the calculator will not compute

Two edges. Both show up in hardware under other names.

x → 0: the object slides onto F. Then x' = f²/x runs away to infinity. Outgoing rays go parallel. That is a collimator, a searchlight, a telescope used backwards. The calculator prints a message instead of a numeric infinity. x = 0 is a regime, not a blank field.

x → ∞: the object recedes. Then x' → 0 and the image sits on F'. Landscape in front of a camera, a star on an objective: the sensor is parked in the focal plane. The farther the object, the less Newton has left to do — drop a screen on F' and you are done.

The two limits answer each other. Object at the focal point ↔ image at infinity. Object at infinity ↔ image at the focal point. Gaussian language says dₒ = f and dₒ → ∞. Here it is just shorter.

Chaining elements without a mythical centre

A compound system is a row of focal points. One element's image is the next element's object. With Newton, each stage keeps its own F, F', x, x'. You chain the products x·x' = f² and never have to rebuild an optical centre that is not sitting anywhere you can touch.

That is why designers talk in focal planes, not in “middle of the glass”. An eyepiece is parked on an intermediate image that already sits at the objective's focal point in an afocal telescope. A 4f relay puts an object at F of the first lens and picks the image up at F' of the second. Newton names those parking spots in one symbol: x = 0 on one side, x' = 0 on the other.

You do not need O to decide whether a doublet's image will land on a sensor. Know F' of the system — and the leftover x' to the useful plane — and you are finished.

Why camera-lens datasheets quote back focal length

A lens sheet lists a focal length and a back focal length (BFL). They are not the same number. Focal length is H' to F', principal plane to rear focal point. BFL is last glass to F' — the rear vertex, the thing you can see.

A “50 mm” may have a BFL of 38 or 40 mm. That gap is what lets a reflex mirror swing up, or a focal-plane shutter sit in front of the sensor. The principal planes of a Double-Gauss or a retrofocus wide-angle are nowhere near the barrel markings. If you treated 50 mm as “glass to chip”, the numbers would lie.

Newton starts at F', not at the last surface and not at H'. Once a datasheet (or a bench) has told you the BFL, you know where F' sits relative to the metal. x' is then a stub beyond that pin. That is the reason BFL is quoted at all: it is the one length that turns a packaged lens into a Newton origin, without ever locating O.

Newton's form on an optical rail

The lab move is older than most of the glass on the shelf. Find F' first: distant object (a window across the yard, a collimator), screen sharp, mark the rider. Flip the lens, mark F. Only then bring in a real object, and measure from those marks, not from the lens holder.

Those two readings are x and x'. Slide the object, and the product should stay f². If it drifts, the lens is not where you think, or F was pinned badly. That check is kinder than a 1/d plot, where a millimetre error on the “centre” of a thick holder walks straight into f.

On a teaching rail, f is often 100 or 200 mm and the riders read to a millimetre. Set x = 50 mm, look for x' = 200 mm, and read |γ| off a millimetre scale on the object. If the image is sharp and |γ| comes out 2, Newton held. Sharp image, wild |γ|: the focal pins have slipped, not the algebra.

Related calculators