EN

Calculate How Much Paint You Need (Litres, Tins)

Buying too little paint means an extra trip to the shop mid-job; buying too much leaves open tins drying out in the shed. This calculator works out the net area to paint in a room — walls minus doors and windows, ceiling optional — and how many tins to buy based on the paint's coverage and the number of coats.

Area to paint

Room dimensions

Deducted at a flat 1.8 m² per door.

Deducted at a flat 1.2 m² per window.

Paint

Used only when "Custom" is selected above.

Known area

Already net of doors and windows, if you worked it out yourself.

Paint

Used only when "Custom" is selected above.

doorwindowheightone wall face (illustrative)
Illustrative diagram: one wall face, to be repeated mentally on all four walls.

Starred trade terms open in the glossary at the end of the page.

Spreading rate on the tin versus the wall

Coverage printed on a tin is a laboratory number. Smooth board, sealed, one even pass with a roller. A hallway with woodchip is not that board. The spreading rate* — square metres per litre, one coat — drops as soon as the surface drinks, as soon as it has texture, as soon as the colour is heavy with pigment. US data sheets often quote square feet per gallon; this calculator stays in m²/L throughout.

  • Porous — bare plaster, fresh skim, new plasterboard: it drinks. Coverage can fall 20–40% against a previously painted wall. Skip primer and the first coat vanishes into the paper face.
  • Already painted, washed down — closer to the label. Knock another 10% off if the old film is patchy, chalky in places, or still showing sugar-soap marks.
  • Texture — Artex, woodchip, heavy lining paper: more real area than the tape measure. Litres sit in the lumps. Fifteen to thirty percent extra is geometry, not caution.
  • Colour — a vinyl white stretches further than a deep red or a navy. Dense pigment makes the film heavier; the roller starts to drag sooner.

The drop-down on this page is a starting point (new surface, roller): about 8 m²/L for primer*, 10 for vinyl matt*, 12 for silk or eggshell*, 11 for oil-based, 6 for masonry. The figure that counts is the one on the tin in the basket — Custom, then type it in.

Volume (L) = area × coats ÷ spreading rate  ·  tins = round up (volume ÷ tin size)

Forty-two square metres, two coats, 10 m²/L: 8.4 L. In 2.5 L tins that rounds up to four tins, 10 L bought. The spare is cutting-in, a bit on the sleeve, a touch-up in two years — not waste.

One coat, two coats, three

Most walls take two. The third coat is not a virtue. It is the colour that still flashes. A single coat only earns its keep on a sound film already close in shade — a same-colour refresh, a small patch, a high-opacity renovation paint sold as “covers in one”. On a 12 m² chimney breast already in cream vinyl, it can look fine. Across four walls of a living room, it rarely does.

Two thin coats always beat one heavy one. The first evens the suck and keys the surface. The second is the colour that was paid for. Pile it on and the film sags, orange-peels, takes forever to go off, and still shows holidays the next morning.

  • One — nearby shade, film still sound, or a “covers in two” paint used as a genuine one-coat on a small area. Exception, not a method.
  • Two — ordinary walls and ceilings. The default on this page, and the figure on most interior emulsion data sheets.
  • Three — dark over light or the other way round, thirsty new plaster, a thin tin, a south-facing room that shows every miss at ten in the morning.

The third pass is justified when the second still leaves windows — patches where the ground shows through. Not before.

Primer and mist coat

Skipping the primer to save a pass is how a job spends two extra finish coats. Primer is not cheap topcoat. It seals the pore, evens the suck, holds back a stain. Leave it out and the first finish coat does that job instead — badly, because it was not made for it.

  • Bare: plaster, plasterboard, timber, metal. Non-negotiable. On new board, primer also stops taped joints telegraphing in raking light.
  • Old chalky emulsion, mixed sheens on one wall, nicotine, a damp patch already treated.
  • A big colour jump. A white undercoat, or better a mid-grey, can save a whole finish coat. The litre of primer is almost always the cheap litre.

New skim drinks. Most emulsions want a first pass thinned — around 10%, sometimes more, check the tin. That is the mist coat*: it soaks in and binds; it does not try to film yet. The second coat goes on neat. A sound silk in a nearby shade, washed, can take finish straight on. “It had paint on it” means nothing if it powders under a fingernail. Masking tape, ripped off in one pull, should not bring the film with it.

Vinyl matt, eggshell, silk

Sheen is wear, light, and how honest the plaster is — not a mood board. The glossier the film, the better it washes, and the more it shows roller lines, dents, and every joint.

  • Vinyl matt — soaks light, hides knocks. Ceilings, bedrooms, a wall that is not quite true. Marks easily; wipe it and a shiny patch appears.
  • Eggshell — the middle. A little wash, a little hide. Living rooms, studies, a hallway that is not hosed down. Water-based eggshell now does most of the work that used to need oil.
  • Silk / satin — scrubbable, a bit of bounce. Kitchens, bathrooms, halls. Also shows roller lines and every bump. Silk on a wavy ceiling reads as soon as low sun hits it.
  • Gloss — doors, skirting, woodwork. Hard film. The timber has to be flat or the finish becomes a mirror of every dent.

Silk on an uneven ceiling is readable at ten in the morning. Matt in a kitchen keeps the first tomato splash forever. The right sheen is the one the room and the wall can carry, not the one that looked best on the fan deck.

Emulsion or oil-based

On walls, water-based emulsion won, and not as a fashion. Quick dry, low smell, brushes in the kitchen sink, a film that moves a little with the house. Recoat in two to four hours, longer if the room is cold and damp.

Oil-based (alkyd, solvent) is the hard film: woodwork, radiators, a wet room wiped daily. Trade-off: white spirit, a real smell, six to eight hours between coats, sometimes overnight. It belongs on the joinery. Painting a whole flat in it “because it washes” buys fumes and a long recote for a job water-based eggshells now cover. Keep the solvent tin for doors, frames, radiators, not for the chimney breast.

Emulsion over old gloss with no key — it can peel like a sticker. Oil over fresh emulsion can wrinkle; the solvent bites a film that has not yet hardened. Read both tins. Systems are not mixed because a leftover stood under the stairs.

Ceiling paint as a separate sum

A ceiling is not a fifth wall. Different paint — usually a more fluid matt, made to work overhead — different spreading rate, different sum. Ticking the box here adds the square metres, but one coverage for the lot. If the ceiling tin says 12 m²/L and the wall 10, the calculator runs twice.

New or thirsty ceiling: primer, then two coats. Sound white on white, washed: two coats of matt will often do. Leftover wall silk is not a ceiling finish “to use it up”. The light is wrong and so is the sheen: silk overhead shows every ridge, and wall matt on a ceiling washes poorly without needing to.

Ceilings are painted first. Splashes land on walls still to be done. Reverse the order and later work is spent hiding silk drops on matt, or the other way round, and the join shows.

Batch numbers and boxing

Same shade name, two tins, two batches: a join shows in raking light, worse in a strong colour. Machine-tinted pots — mixed in the shop, not at the factory — are the twitchy ones. Half a shade, invisible on the lid, draws a stripe as soon as daylight rakes the wall.

The whole quantity is bought in one go. The batch number* is read on every lid. Several tins of one batch: open them, pour into a kettle, stir — boxing*, the old word. Changing tins halfway along a wall is how a stripe gets painted. One wall, one mix. Room too big for a single batch: break at a corner, never mid-face.

The code on the lid is not a warehouse detail. It is what decides whether two tins of the same name are actually the same paint.

Worked example: a 20 m² living room in two coats

Room 5.00 × 4.00 m, ceiling 2.50 m, one door, one window. Walls only, silk emulsion at 10 m²/L, 2.5 L tins. This page knocks off a flat 1.8 m² per door and 1.2 m² per window — not a tape-measure of each opening, close enough while the openings stay in that range.

  • Perimeter = 2 × (5.00 + 4.00) = 18.00 m
  • Gross walls = 18.00 × 2.50 = 45.00 m²
  • Openings = 1.8 + 1.2 = 3.0 m²
  • Net area = 45.00 − 3.0 = 42.0 m²

Volume = 42.0 × 2 ÷ 10 = 8.4 L  →  tins = round up (8.4 ÷ 2.5) = 4 tins of 2.5 L

So 10 L bought for 8.4 L used. The spare is cutting-in, a bit on the roller, a touch-up later. Ceiling on its own, 20.0 m², matt at 11 m²/L, two coats: 20 × 2 ÷ 11 ≈ 3.6 L → two 2.5 L tins.

The floor is not in those litres. Once the walls are laid off, boards or laminate are ordered in packs, with a cutting allowance, not in tins. Paint first, lay after: splashes do not land on new planks.

Thinning the first pass

On new plaster, many emulsions want the first coat a little wetter — 5 to 10% water, sometimes more, according to the tin. That is not stretching the paint to make it go further. The binder needs to enter the grain before a film is laid. The second coat goes on as it comes.

Thinning a silk “because it feels thick” is how opacity and flow are lost. A silk thinned on a whim leaves roller tracks that never lay off. The tin is followed, not the bucket in the van, and not a shelf note written for a different product.

Doors, patio doors, radiators

The 1.8 / 1.2 allowance covers an internal door and an ordinary sash. A 2.40 × 2.20 m patio door is measured, Direct area is used, or the real opening is subtracted from the walls. Radiator left on: almost nothing is painted behind it, so almost nothing is deducted. Radiator off the wall: the bay is all paint, deduct nothing.

Built-in cupboard, stove, a run of kitchen units: the same logic. Deduct too much and another tin is needed mid-job, often from another batch. Deduct too little and an open tin skins over in the shed. Direct area also covers a room that is no longer a rectangle — an L, a stairwell, a sloping ceiling.

Dust-free, recoatable, hard dry

Dust-free is not recoatable. Recoatable is not hard dry. Everyday emulsion: dust-free inside an hour, recoatable in 2–4 h, longer if the room is cold and damp. Oil-based: half a day, often overnight. The data sheet always beats these rules of thumb.

Go back too soon and the roller pulls. Leave some emulsions several days and the second coat keys less — a light rub-down then, nothing heroic. Recoat time is not a tea break. It is the time the film will take another coat without tearing.

Strong colours and a grey ground

Reds, yellows, deep blues: hiding power falls off a cliff. Two finish coats over white still flash. A high-opacity renovation paint helps. A mid-grey primer helps more: it kills the contrast before the colour goes on. Aubergine to off-white with no undercoat is three or four finish coats, paid for twice.

Organic yellows and reds are the ungrateful ones. Mid-grey under a red, white under a beige, and the coat count comes back down. The litre of primer remains the cheap litre, especially when the pigment is a poor hider.

Glossary

Spreading rate
Area covered by one litre in one coat, in m²/L. The figure on the tin is a lab test on a sealed board. Site coverage falls as soon as the wall is porous, textured, or painted in a heavy colour.
Primer
A sealing or gripping coat, not a thinned finish. It closes the pore, evens suction and gives the topcoat something to hold. On stains, a dedicated isolating primer; on new plaster, often a mist coat plus a primer as the tin directs.
Mist coat
First pass of emulsion, thinned (often about 10% water) on new plaster or skim. It soaks in and binds the surface instead of sitting as a film. The following coat is applied neat.
Batch number
Factory (or in-store tint) code printed on the lid. Two tins of the same shade name from different batches can still show a join in raking light, especially in a strong colour.
Boxing
Pouring several tins of the same batch into one kettle and stirring before cutting in. It averages small shade differences and stops a stripe appearing mid-wall.
Vinyl matt
A flat water-based wall paint. It hides defects and soaks light, which is why it is the usual ceiling and bedroom finish. It marks more readily than eggshell or silk and does not like hard washing.
Eggshell
A low sheen, between matt and silk. Washable enough for living rooms, still decent at hiding. Water-based eggshell has largely replaced oil eggshell on walls.

Related calculators