EN

Calculate Your Swimming Pool Volume (Litres)

A pool's water volume matters for two things: sizing the filtration (the whole volume needs to be filtered several times a day) and working out the amount of product for a treatment — typically a shock chlorine dose after opening the pool or to clear green water. Pick the pool's shape and enter its dimensions.

Sloped floor? Use the average depth: (shallow end depth + deep end depth) ÷ 2. For an irregular shape (a rectangle with a rounded corner, for example), work out each part separately and add the volumes together.

Shape and dimensions

Dimensions
Treatment (optional)

Indicative: 20 g/m³. Check the dose printed on your chosen product's packaging.

Dimensions
Treatment (optional)

Indicative: 20 g/m³. Check the dose printed on your chosen product's packaging.

Dimensions
Treatment (optional)

Indicative: 20 g/m³. Check the dose printed on your chosen product's packaging.

lengthwidthtop-down view (depth not shown)
Top-down view, rectangular shape.

Starred terms are spelled out, in plain language, in the glossary at the bottom of the page.

Average depth on a hopper floor

A “12,000-gallon pool” is three different amounts of water, depending on which gallon the last owner had in mind. This page works in cubic metres, on purpose. One cubic metre* is a thousand litres — about 220 imperial gallons, or 264 US gallons. Mix those two gallons on a label, and the shock dose is already wrong before the bag is open. The depth is where most of the remaining error hides.

On a sloping floor the shallow end is not the answer, and neither is the deep end. They average. The slope itself — the rise between those two water depths — is the same arithmetic as a ramp or a roof, and the slope calculator in this chapter will put that rise in percent or in degrees. For the volume of water, only the mean of the two depths goes into the formula, not the angle.

havg = (hshallow + hdeep) / 2

A floor that runs from 0.90 m to 1.80 m is 1.35 m, not “call it 1.80 to be safe”. Ten percent extra depth is ten percent extra shock* — and a pump sized for water that is not actually there.

Flat floor, typical of a steel-wall above-ground: the average is the water depth, read at the wall under the skimmer*. A beach area at one end and a hopper at the other are two volumes. Split them. A single mean squashed across the whole plan describes water that exists nowhere in the basin.

Filter turnover: matching flow to the basin

Pool engineers talk turnover: the whole volume through the filter, once, in four to six hours. That sets the flow. A municipal indoor pool aims tighter. A garden pool does not have to copy a leisure centre.

flow ≈ volume / turnover time  ·  40 m³ / 5 h = 8 m³/h

Eight cubic metres an hour on forty cubic metres is the flow of one lap, not “the biggest pump on the shelf”. Run time is a separate question. Four to eight hours a day covers most private pools. A heatwave, a bank-holiday crowd, a spell of green: longer. Idle water grows things in the corners. Over-run the pump and the sand, the cartridge clamp and the electricity meter wear for nothing.

A sand, cartridge or DE filter whose rated flow sits near that figure, with a little headroom — not twice “just in case” — is the usual pairing. Undersize it and the thing needs rinsing every other day. Oversize it and the water slips through barely cleaned: the bed never has time to catch what it should. Pump and filter are chosen as a pair. Volume says how much water there is. The pump says how long a lap takes. A feeble backwash never fluidises a sand bed; a violent one sends sand out of the laterals.

Shock dose, trichlor tabs, bromine, salt chlorinator

Four families. They do not share a bucket, and they are not stacked “to be on the safe side”. Each has its own chemistry, its own strength, its own moment.

  • Shock dose — spring opening, green water, after a storm. Dichlor or calcium hypochlorite, as a rule. The pack is the authority: 56 % available chlorine is not 65 %.
  • Slow-release — trichlor tabs in a floater or the skimmer. Week-to-week residual. On a vinyl liner, a tab left in the basket can bleach a stripe overnight.
  • Bromine — spas, indoor pools, anyone who hates the chlorine smell. Different molecule, different tablets, a wider pH window. Dearer.
  • Salt chlorinator* — a cell makes chlorine from dissolved salt. The salt is not used up. Splash-out and a partial drain are what get topped up, from a starting level around 3 to 5 g/L.

Shock is not “an extra tab”. A trichlor tablet releases chlorine slowly, and it brings stabilizer with it. Shock aims at a spike. Salt does not excuse the pH*, or the alkalinity, or a filter that actually runs. None of these families washes the water in place of the sand.

Switching from tabs to a salt cell mid-season is possible. The stabilizer has to come down first — which means replacing a share of the water — before the cell does useful work.

pH first, or the chlorine sits idle

Chlorine that actually kills is hypochlorous acid (HOCl). Push the pH up and it tips into the hypochlorite ion, a much weaker disinfectant. The useful window for a chlorinated pool is 7.0 to 7.4. Past 7.8, a large part of the dose never reaches the algae.

aim for pH 7.0 – 7.4  ·  outside it, chlorine is half-asleep

Fix the pH first. Then shock. The other way round is money poured into water that will not use it. A reading that will not sit still, day to day, is often not a chlorine problem. It is total alkalinity too low, the buffer gone, so a shower of rain or a crowded afternoon throws the number around.

Total alkalinity usually sits between 80 and 120 mg/L as CaCO3. Too low, bicarbonate brings it up. Too high, acid brings it down in small doses, pump running — never a whole jug in one corner. The pH is read after that mix, not during it.

In short, three readings before a shock: pH, alkalinity, and the free chlorine already there. A basin already holding 3  ppm* of free chlorine does not need the same scoop as a green soup sitting at zero.

Above-ground or in-ground: the same cubic metres

Same litres. An 8 × 4 steel-wall pool and an 8 × 4 concrete shell, same water depth, hold the same cube. The formulae do not care how the hole was made, or whether the wall is steel, timber or block.

rect. = L × W × havg  ·  round = π r² h  ·  oval = π a b h

a and b are the semi-axes, not the full diameters. An oval 6 m by 3.5 m is not π × 6 × 3.5 × h. It is π × 3 × 1.75 × h. That slip, a common one, roughly quadruples the volume, and the dose with it.

What does change is not the litre. Above-ground floors are usually flat. The skimmer is clamped to the wall at a height the liner dictates. Ice on a badly winterised wall splits steel and tears a liner hanging on a dry panel. Overflow channels are rare on a garden steel-wall, common on a high-end in-ground. The water in the basin is still the same calculation.

Kidney, roman end, lazy-L: split the plan

There is no magic kidney formula. The plan is cut into pieces that can be measured, each piece is worked, and the volumes are added.

  • A centre rectangle plus two half-circles — the brochure’s “round-ended oval”, which is not a mathematical ellipse.
  • Roman steps: their own plan area times their own, shallower, water depth. Skipping them under-counts a little. Counting them at the deep-end depth over-counts a lot.
  • A beach and a hopper: two prisms, two depths, a sum. Not one mean laid over the whole surface.

A builder’s drawing, a tape over the coping, even pacing it out, beats “the last owner said 12,000 gallons”. Those 12,000 gallons on a sales sheet are often a commercial round number, and they do not say which gallon.

Still, a five-percent miss on a kidney split cleanly is fine for a shock. A shape error — treating a long axis as a radius, giving the steps the deep-end water — costs more.

How much water to replace each year

Filtration takes particles out. It does not reset the chemistry. Sunscreen, sweat, pollen, hardness concentrating with every top-up, cyanuric acid from the tabs that never leaves. A partial drain, about a third of the volume once a year, puts those concentrations roughly back in range.

On a 40 m³ pool that is a dozen cubic metres, not forty. It is often done at opening, or after a summer of generous tabs, when the stabilizer has climbed past 80 ppm and shock “no longer takes”.

Emptying an in-ground shell to the floor, on a high water table, is how a pool floats — literally. Costly in water, heat and rebalancing besides. Drop a third, refill, reset pH and alkalinity. Waste water goes where the local rules say, not down the ditch: residual chlorine and dissolved salts have no business in a stream.

A partial drain is not a failure of the filter. It is the only move that lowers what the filter cannot catch.

Worked example: shocking a 40 m³ pool at opening

Ten metres by four, flat floor at 1.00 m — a typical rectangular garden pool in the UK, opened after a dull April under a cover. Volume = 10 × 4 × 1.00 = 40 m³, which is 40,000 litres, about 8,800 imperial gallons or 10,600 US gallons.

amount ≈ 40 m³ × 20 g/m³ = 800 g of shock

Twenty grams per cubic metre is this page’s ballpark, not the number on the tub in the shed. Dichlor at 56 % is not cal-hypo at 65 or 70 %. The label for 40 m³ is what gets weighed, not the neighbour’s scoop. Eight hundred grams of one is not eight hundred grams of the other.

  1. Brush walls and floor, empty the baskets, pump running. Shocking a soup of debris feeds the algae as much as it hits them.
  2. Bring pH into 7.0–7.4, alkalinity into its window. Wait for a mix, read again.
  3. Pre-dissolve in a bucket of pool water — product into water, never water onto a heap of powder, never two chemicals in one bucket.
  4. Broadcast, away from a bare liner if the product is cal-hypo. Filter for 24 h. No swimming until free chlorine is back near 1 to 3 ppm.

Never mix chlorine and acid, chlorine and algaecide, tabs and shock in the same container. Chlorine gas is not a metaphor. One product, wait, then the other — or a clean bucket. The pack of the product in hand always outranks the figure on this page.

The figure is a sound estimate for most simple shapes. A kidney, a beach area or a floor with more than one slope deserves a finer take-off. The dose on the pack is not negotiable.

Litres, imperial gallons and US gallons

This calculator is metric. That is not a snub to anyone who still thinks in gallons. It is a way not to pick the wrong gallon. An imperial gallon is 4.546 litres. A US gallon is 3.785 litres. The gap is about 20 %. A US “12,000-gallon pool” holds roughly 45 m³. A UK “12,000-gallon pool” holds about 54.5 m³. Treat those two sales lines as the same basin, and the shock is out by a fifth.

Worth knowing, if a US forum or a US pack is the source of a dose in “pounds per 10,000 gallons”: those gallons are US gallons. Convert to cubic metres first, then apply the grams-per-cubic-metre figure, rather than mixing the two systems in one sum.

1 m³ = 1,000 L ≈ 220 imp gal ≈ 264 US gal

Skimmer versus overflow

A skimmer draws at the surface film — pollen, sunscreen, the greasy layer a sand filter would see too late. The waterline sits about two-thirds of the way up the mouth. Too low, the pump gulps air and the weir gasket dries. Too high, nothing skims: water slips under the flap and the surface stays dirty.

A deck-level overflow, or a perimeter weir, lets the whole surface sheet into a balance tank. Cleaner top, more pipe, more money, and a tank volume to add if the treatment is sized on the whole circuit. The basin volume on this page does not change. The hydraulics do.

An above-ground almost always has one skimmer. An in-ground from a catalogue may have two, facing the prevailing wind. The water volume is still the same. The suction is not.

Total alkalinity and hard fill water

Alkalinity buffers the pH. Calcium hardness is the scale story: heating elements crust, tile grout grows a collar, a vinyl liner feels gritty. Fill from a hard mains, common on chalk in the south-east of England, and every top-up concentrates the stuff further.

A domestic softener is not dropped onto a pool and forgotten. A unit left on the fill line, badly set, sends water so soft it attacks metals and makes the pH twitchy. Watch the fill, go easy on cal-hypo — it brings calcium of its own — and descale what needs it.

Borehole water is not mains water. Iron, manganese, sometimes a pH already low. A test of the fill, before 40 m³ go in, beats discovering the stain once the liner is down.

Winterising a liner without splitting the wall

Mild winter, pump still circulating a few hours, cover on: active close-down, the usual choice in much of the UK. Hard freeze: drop the water below the skimmers, fittings out, freeze plugs in, something floating so ice has somewhere to go, dark cover.

An above-ground wall that ices unevenly splits. A liner hanging on a dry wall tears. Volume here is only so the winter chemical can be dosed — again the pack, not a family recipe — and the dose is worked on the water that remains, not on the summer volume if the level has been dropped.

Winterising is not a different trade. It is the same volume, a slower clock, and the same refusal to mix two products in one bucket.

Glossary

m³ (cubic metre)
The volume unit this page uses. 1 m³ = 1,000 litres ≈ 220 imperial gallons ≈ 264 US gallons. Filter flow and chemical weights are both set from this number.
ppm
Parts per million. In pool water, 1 ppm is 1 mg/L, which is also 1 g/m³. Free chlorine is commonly read in ppm (a typical residual is 1 to 3); a shock aims at a much higher spike, briefly.
Shock dose
A short, high dose of chlorine for opening, green water or after a storm. Not an extra tablet. Powder or granules, strength varying by brand: the pack for the calculated volume is what gets weighed.
Salt chlorinator
A cell that makes chlorine in the water from dissolved salt (typically 3 to 5 g/L). The salt is not consumed; the cell is. pH and alkalinity still need watching.
Skimmer
The surface suction box that takes the floating film — pollen, oils, debris. The waterline sits part-way up the mouth. Too low, the pump draws air; too high, nothing skims.
pH
A scale of how acidic or alkaline the water is. Chlorine disinfects mainly as hypochlorous acid, which dominates between about 7.0 and 7.4. Outside that window the same grams do less work.

Related calculators