Moment of Inertia Calculator (Mechanical Parts)
The moment of inertia measures how much a part resists a change in rotational speed — the rotational counterpart of what mass is for straight-line motion. It depends not just on mass, but on how that mass is spread around the rotation axis: the farther the material sits from the axis, the larger the moment of inertia.
Pick the shape, enter the mass and dimensions: the calculator returns the moment of inertia I and the radius of gyration k = √(I/M) — the distance at which you'd need to concentrate the entire mass to get the same I.
The part
A short glossary sits at the foot of the page; the asterisk marks the first mention only.
Moment of inertia versus mass: why the distribution matters as much as the amount
Mass fixes how hard a body is to shove in a straight line. Spin is a different argument. What counts is how far that mass sits from the axis. The name for the spread is the mass moment of inertia*.
A kilogram parked on the axis barely notices a change of speed. The same kilogram at the rim resists, because every bit of mass enters the sum through r²: twice the radius, four times the inertia. Two parts of equal mass can run like different machines. A solid disc keeps material all the way in. A hoop, or a spoked wheel of the same mass, parks it at the rim. The hoop carries the larger I, and it takes more torque to spin up. Reading acceleration off the kilograms alone is only half the story. Where those kilograms sit is the other half.
I = Σ mi · ri² · I = ∫ r² dm
The SI unit is the kg·m². For a handful of workshop shapes, about the axis drawn on the diagram, that is the number returned here. A geometric moment of a cross-section is a different object, with a different unit. It turns up later, and it does not convert into this I.
The radius of gyration*: what it is actually used for
k is the radius of a thin hoop that would carry the same I and the same mass. The result line prints it as k = √(I / M). Some texts write i or ρ for that same length. Strength-of-materials tables reuse i for a section radius of gyration, √(Iarea/A): centimetres of geometry, not this k.
k = √(I / M) · I = M · k²
- Solid cylinder, axis through the centre: k = R / √2 ≈ 0.707 R
- Tube, same axis: k = √((Rint² + Rext²) / 2)
- Thin rim: k ≈ R
- Solid sphere, diameter axis: k = R √(2/5) ≈ 0.632 R
Two rotors are compared on k, not on mass. A tube and a solid bar of the same kilograms: the tube’s k sits closer to the outer radius, and its I is larger. The whole flywheel argument fits in that one length. k is not a dimension a caliper can read. It is a summary of the sum r² dm.
Parallel-axis theorem*: moving from a central axis to an offset axis
The formulae here are for a centroidal axis: through the centre of mass, in the direction the sketch shows. A hinge, a robot joint, a shaft that is not the part’s own axis — that axis lies somewhere else. The shift is the parallel-axis theorem, also called the Huygens–Steiner theorem.
Ioffset = IG + M · d²
IG is the centroidal value already returned here, or read from a table. d is the distance between that axis and the parallel axis of the spin. The added term is always positive: I about any parallel axis is larger than IG. The rod in the menu is the textbook check. Centre: M L² / 12. End: M L² / 12 + M (L/2)² = M L² / 3, which is the other rod option on this page. The axis through G has to be parallel to the new one, and it has to pass through the centre of mass, not through a guessed geometric centre. For a cluster of lumps, G comes first from the centre-of-gravity calculation.
No tilted-axis rule has the same simplicity. A rotation axis at an angle is a tensor, or a CAD output. Off the principal directions that tensor carries a product of inertia*, Ixy = ∫ x y dm. On a symmetry axis the product is zero. Tilt the axes and it is not. M d² does not cover that case.
Sizing a flywheel: why a heavy rim beats a solid disc
A flywheel stores kinetic energy between the strokes of a piston engine, a press or a punch, and keeps the machine from stalling. For a given mass and a given outside diameter, the useful I is the largest the envelope allows. That means mass at the rim, a skinny hub, and spokes that only have to survive hoop stress.
A thin ring of mass M and radius R has I = M R². A solid disc, same M, same R, has I = ½ M R². Twice the inertia for the ring, same kilograms, same envelope. Hollow against solid, at fixed outside diameter, is the same contrast: the bore throws away the material that was doing the least work in the sum r² dm. Energy stored is ½ I ω². Speed adds joules as well. Doubling rpm quadruples the stored energy, until the rim bursts. Steel rims on industrial wheels live at a few thousand rpm. Composite energy-storage flywheels go much higher and fail by fibre, not by a mild steel hoop. A solid disc remains the lazy shape: cheap to machine, wasteful of mass.
Iring = M R² · Idisc = ½ M R²
What actually gets cast is a thick rim whose mean radius sits a little under R. The tube option, with Rint close to Rext, is the match for that rim.
Torque and angular acceleration: Γ = I·α
Newton’s second law, written for a spin axis. Some books use T or τ for the same torque. Γ here is that couple, in N·m. I is the mass moment about the same axis, in kg·m². α is the angular acceleration in rad/s² — not in rpm per second until the conversion is done.
Γ = I · α
Motor and brake sizing live on that product. A target of 200 rad/s² on a rotor of 0.15 kg·m² calls for 30 N·m at the shaft, plus whatever friction and process load sit on top. Cutting I makes the same motor feel snappier: a light rim, a smaller diameter, lightening holes placed out towards the rim rather than near the hub. Holes near the rim remove the mass that was contributing most to I; holes near the hub barely register. A flywheel is the other brief. Large I, so a given torque barely changes speed. That is the point of the smoothing.
From rpm to rad/s² the step is α = 2π (N₂ − N₁) / (60 Δt). A motor quoted as “0 to 1,500 rpm in 0.4 s” on a 0.05 kg·m² drum is asking for about 20 N·m. The datasheet is checked against I, not against a feel for kilograms.
Rotational kinetic energy: E = ½·I·ω²
Same kinetic energy as ½ m v², with I in place of m and ω in place of v. ω is radians per second. 1,000 rpm is 104.7 rad/s, not 1,000.
Erot = ½ · I · ω² · dE = Γ · dθ
A 0.27 kg·m² rim at 3,000 rpm (314 rad/s) holds about 13 kJ. A few seconds of a small motor, or the dip between two cylinder firings. Double the speed, four times the energy. Double I, only twice. Energy-storage flywheels chase rpm until hoop stress, bearings and windage say no. A grinding-wheel guard is sized for that stored energy, not for the mass of the wheel. On a rotor within reach while it spins, the hazard is the joules, not the kilograms.
The work identity dE = Γ dθ is Γ = I α, integrated. A brake that dumps 13 kJ in a quarter turn has to put up a very large couple for a very short time.
A part built from several simple shapes
A real rotor is a stack of discs, a tube, a key, a hole. I about one axis is a sum, after every piece has been shifted onto that same axis.
- Chop the part into volumes this page already knows: disc, tube, rod, plate.
- Take IG of each piece about its own centre of mass, parallel to the global axis.
- Add M d² for the offset of that centre from the global axis.
- Holes and keyways are negative pieces: subtract their IG + m d².
- Add what remains.
CAD does the same thing with tetrahedra. A hand calculation is the same algorithm with six lumps instead of six thousand. The axis has to be the same one for every term. Mixing a plate’s face-normal I with a cylinder’s long-axis I is how a report picks up a factor of two, unnoticed until the servo saturates.
The practical order is the other way round. Weigh the weldment, measure G, and hang the whole thing and only chop it on paper if the test and the model disagree.
Mass moment of inertia versus the second moment of area*
Same letter I. Different quantity, different unit, different job.
- Mass moment of inertia — kg·m². Dynamics. This page. How hard the part is to spin.
- Second moment of area — m⁴. Geometry of a cross-section. How stiff a beam is in bending. No mass in the formula.
- Section modulus* W (AISC: S) — m³. Geometry again. Extreme-fibre stress σ = M/W. That number is what the section-modulus calculation returns.
A CAD property manager labelled “Ixx / Iyy / Izz” is almost always the mass moments of the solid, in the document’s mass-length units. A steel table labelled Iy = 1,943 cm⁴ is the area property of a beam. Paste one into the other and the powers of ten do not even look wrong. The radius of gyration of a section is √(Iarea/A). The radius of gyration of a rotor is √(Imass/M). This page prints the second, as k.
A unit of m⁴, cm⁴ or mm⁴ belongs to strength of materials. A unit of kg·m², g·cm² or lb·in² belongs to rotational dynamics. No conversion exists between those families. They are not the same I.
Measuring a moment of inertia: the bifilar pendulum*
Two equal wires, length L, hang parallel. The attachment points sit a distance d apart on the part — full spacing, not half. Twist the part a few degrees about the vertical and let go. Time several small oscillations and divide. That period is T.
I = (M · g · d² · T²) / (16 π² · L)
The rig needs a mass, a tape and a stopwatch. The wires must share the load, stay parallel and stay equal. A trifilar hang, three wires, is more forgiving on a lopsided casting. Small angles only. A quarter turn is not a bifilar test; it is a mess. A part that can pivot on a knife-edge is the simpler rig, a physical pendulum: T = 2π √(I / (M g h)), with h the distance from the pivot to G, so I = M g h (T / 2π)². That I already includes the parallel-axis shift out to the pivot.
The hang checks a CAD number. It does not replace a drawing of a simple disc. When the test and the model differ by more than a few percent, look for a density left at 1,000 kg/m³, or for a weld bead nobody put in the solid.
Worked examples: engine flywheel, bicycle wheel, drive shaft
Three rotors. Three different reasons to care about I.
Engine flywheel
First as a solid steel disc, 300 mm in diameter, 25 mm thick. Volume π R² t ≈ 1.77×10−3 m³. At 7,850 kg/m³ that is about 13.8 kg. About its own axis:
I = ½ · 13.8 · (0.15)² ≈ 0.155 kg·m²
The same mass parked in a rim of mean radius 0.14 m gives I ≈ 13.8 × 0.14² ≈ 0.271 kg·m², about 75% more. That rim swallows the firing pulses better. The starter motor has to live with the larger I on cranking.
Bicycle wheel
A typical 700c wheel, tyre and all, is around 1.8 kg. Roughly 1.2 kg of that sits in the rim and tyre at about 0.32 m. Hub and spokes lie close to the axis and barely count.
I ≈ 1.2 × (0.32)² = 0.123 kg·m²
A downhill or touring rim, heavier at that same radius, raises I. The first pedal stroke goes duller, and speed holds better on the flat. A racing wheel does the opposite: less mass at the rim, smaller I, snappier accelerations. Rotating mass at the tyre is paid twice — once as translation, once as I α. Rim grams move I more than a slightly heavier hub does.
Drive shaft
Solid steel bar, 50 mm diameter, 1.5 m long. Volume π R² L ≈ 2.95×10−3 m³, mass about 23 kg. About its own long axis:
I = ½ · 23 · (0.025)² ≈ 0.0072 kg·m²
Hollow the same envelope, 40 mm bore. Remaining mass is about 8.3 kg, not 13. I = ½ × 8.3 × (0.025² + 0.020²) ≈ 0.0043 kg·m². Rotating inertia drops by about 40%, mass by about 64%. Torsional stiffness, a polar second moment of area (m⁴), falls to roughly 59% of the solid bar. Not “almost as stiff”: lighter, and it remains serviceable. The shaft-torsion calculation is that other I. Dynamics and strength of materials have just used two different ones on the same tube. The units stay in sight.
Which axis the menu is using
Every formula here is for one axis, the one in the sketch. Swap the axis and I changes, sometimes by a factor of two.
- Solid or hollow cylinder — the central geometric axis, the one a shaft spins on. A disc tumbling about a diameter is ¼ M R² (plus a thin-rod term if it has thickness), not the ½ M R² of the flywheel.
- Sphere — any diameter through the centre. They are all the same.
- Thin rod — an axis perpendicular to the rod, either through the mid-point or through one end. Not the long axis. A needle about its own length is tiny, and this page does not return it.
- Rectangular plate — the axis through the centre, perpendicular to the face (Izz of the plate). In-plane axes are M b² / 12 and M a² / 12. The perpendicular-axis theorem says they add up to the number printed here.
The axis belongs on the calculation, the way a datum belongs on a drawing. “I = 0.155 kg·m²” without an axis is an unfinished sentence.
CAD reports, g·cm² and the powers of ten
SolidWorks, Inventor and Creo will dump Ixx, Iyy, Izz in whatever unit the part file uses. A model in millimetres often reports kg·mm². 1 kg·m² = 106 kg·mm² = 107 g·cm². Shift the decimal three places the wrong way and the servo that was sized is a toy, or a crane.
- 1 kg·m² = 107 g·cm² = 3.417 × 103 lb·in² (mass pounds, inches)
- A motor datasheet in kg·cm² is 10−4 kg·m² per unit. 45 kg·cm² is 0.0045 kg·m².
- The principal axes CAD draws pass through the centre of mass, unless the coordinate system was set at the origin of the part. A shaft drawn with one end at (0,0,0) has I about the origin larger than IG by M d². The product of inertia is zero on those same axes.
Before a CAD number goes into a motor spreadsheet, the unit line is read twice and the origin is checked against G. Then the real part is weighed. Density in the model is the usual liar.
Gears, belts and reflected inertia*
A load on the far side of a gearbox does not show the motor its true I. With a reduction n = ωmotor / ωload (n > 1 for a reducer), the inertia of the load, referred to the motor shaft, is Iload / n². A 0.20 kg·m² drum behind a 10:1 reducer looks like 0.002 kg·m² at the motor. The motor’s own rotor, and the high-speed coupling, are already on that shaft and are not divided.
Imotor shaft = Irotor + Icoupling + Iload / n²
A small servo can swing a heavy table through a worm box for that reason, and the same servo, direct-drive, cannot. Belts and leadscrews carry their own reductions — pitch, pulley ratio — and the same 1/n² applies. Efficiency is a separate factor on the torque side. It does not belong in I. On a sloppy gearbox the inertia the motor meets on a reversal is not the tidy number above. Backlash lets the motor accelerate its own rotor first, then hit the load.
Beam bending does not size that servo. W and Iarea belong to the shaft as a beam. This I belongs to the shaft as a rotor. Both enter when the shaft spins up and sags between bearings.
Glossary
- Mass moment of inertia
- How strongly a body resists a change in its spin, about a chosen axis. It grows with the mass and with the square of the distance from that axis. The SI unit is the kg·m².
- Radius of gyration
- The distance from the axis at which the whole mass could sit, as a thin ring, and keep the same moment of inertia. It equals √(I/M). A length, not a caliper dimension of the part. The section radius of gyration √(Iarea/A) is a different length, with no mass in it.
- Parallel-axis theorem
- Also called the Huygens–Steiner theorem. About an axis parallel to one through the centre of mass, I equals the centroidal moment plus mass times the square of the distance between the two axes. The added term is never negative: moving the axis farther out never lightens the inertia.
- Product of inertia
- An off-diagonal term of the inertia tensor, Ixy = ∫ x y dm. It is zero on the principal axes, the symmetry axes of the mass. A non-zero product means the chosen axes are tilted relative to those directions. The parallel-axis shift M d² does not remove it.
- Second moment of area
- A purely geometric property of a cross-section, in m⁴, cm⁴ or mm⁴. Beam tables call the same quantity the area moment of inertia. It measures how the area is spread. No mass enters. Beam bending uses it. It cannot be converted into a mass moment of inertia.
- Section modulus
- The second moment of area divided by the distance from the neutral axis to the extreme fibre. The unit is m³. Bending stress at that fibre is the bending moment divided by this modulus. US steel tables often label it S; elsewhere it is W.
- Bifilar pendulum
- A part hung on two equal, parallel wires and twisted through a small angle about the vertical. The period of that swing, together with the mass, the wire length and the full spacing of the wires, gives the moment of inertia about the vertical axis.
- Reflected inertia
- The inertia of a load as it appears on another shaft after a gear, belt or screw reduction. With a speed ratio n (motor speed over load speed), the load’s I is divided by n² on the way back to the motor. The motor’s own rotor is not divided.