EN

Calculate the Volume and Surface Area of a Cylinder

A right cylinder — two identical circular bases joined by a curved surface — is fully determined by its radius and its height. Handy for a can, a tank, a pipe, or a column.

Enter these two dimensions: the calculator gives the volume, the lateral surface area (the curved side alone) and the total surface area (bases included).

Radius and Height

Dimensions
r = 3 mh = 8 m
Sample diagram. It redraws with the values entered after the calculation.

A starred word is defined in the glossary below.

Unrolling the label: why the curved wall is a rectangle

Peel the paper off a tin. Laid flat, it is a rectangle. That is the net* of a right circular cylinder*, not a coincidence and not an integral.

The rectangle’s height is h, the cylinder’s height. Its width is the distance around the base — the circumference* 2πr, the same length that the circle calculator reports for a disc of radius r. Area of the rectangle: 2πr × h. That is the lateral surface*, lids off. The two ends are discs of area πr² each. Closed can: add them. Open sleeve: leave them out. Total for a sealed drum:

Slat = 2πrh Stot = 2πr (r+h)

The unroll is a rectangle only while the generators stand perpendicular to the base. An oblique cylinder does not flatten that way. Volume, by Cavalieri’s principle, can survive a shear; 2πrh does not. The formulae here are for a right circular cylinder. A leaning flue is a different solid.

Closed can versus open pipe: which surfaces count

Volume never asks whether the ends are on. πr²h is the interior, lids or no lids. Surface area is a shopping list. Paint the outside of a sealed tank: total surface. Line a chimney: lateral only. Cut a gasket from the lid: one disc, πr², which is exactly the area of the circular base.

In practice the question is settled before the arithmetic: what is being covered? Sheet metal for a can includes two lids. A cardboard tube does not. This calculator reports lateral, the two bases, and the total, so the choice stays on the job rather than inside the formula.

Pipe wall: two radii, one subtraction

A pipe, a ring, a length of conduit is not a solid cylinder. It is two cylinders of the same height, outer radius R, inner radius r, and the inner one is removed.

Vhollow = π h (R² − r²) = π h (R − r)(R + r)

The second form helps when wall thickness e = R − r is the known figure. A 2 m run, 10 cm outer radius, 8 mm wall: r = 0.092 m, metal volume π × 2 × (0.10² − 0.092²) ≈ 0.0097 m³, just under 10 L of steel. The volume the pipe carries is the inner cylinder: π × 2 × 0.092² ≈ 0.053 m³, about 53 L.

Surface is a different inventory: outer wall, inner wall, and — if the pipe is cut to length — two annular ends of area π(R² − r²) each. A sleeve that slides on has no such ends. Sketch before metering.

This calculator is a solid cylinder. For a pipe, run two calculations and subtract the volumes. Subtracting the two total surfaces as they stand is wrong: some of the ends vanish, and new walls appear.

Standing drum or lying bowser: same volume, different wetted area

Lay a can on its side. The volume does not care. πr²h has no “up”. 330 ml is 330 ml on the fridge door or on the table. Wetted area does care. Upright, the liquid sees a disc (the bottom) plus a band as high as the fill. On its side, the free surface cuts a rectangle through the cylinder, and the wetted wall depends on how full the vessel is. Exactly half full, half the lateral area plus two half-discs does the job. At any other level, circular segments come into it.

A site bowser laid horizontal still has total volume πr²L (here L plays the role of h). A partial fill needs a circular segment or sector, which is not this page. For sizing the tank, standing or lying, the same formula. The pose is chosen for stability, draw-off height, ground space — not for capacity.

Recovering radius or height from a known capacity

V = πr²h reads both ways. One unknown at a time.

h = V / (π r²)  ; r = √(V / (π h))

A 200 L tank (0.200 m³) with a 50 cm inner radius: h = 0.200 / (π × 0.50²) ≈ 0.255 m, a quarter-metre of water. A drum 80 cm tall that must hold 100 L: r = √(0.100 / (π × 0.80)) ≈ 0.200 m — twenty centimetres of radius, forty of diameter. Diameter is 2r. Feeding the diameter into the radius box multiplies volume by four. The jump is large enough to feel; it still happens.

Volume alone will not yield both r and h. Infinitely many pairs (r, h) share the same V. A second fact is required: a height, a diameter, a ratio h/r, a limit on the footprint. A squat drum and a tall pipe can hold the same amount. The floor they occupy, and the steel they need, do not.

Tanks, silos, cans, and what is not a cylinder

A water tank, 1 m radius, 2 m high: V = π × 1² × 2 ≈ 6.28 m³, so 6,280 L. A grain silo, slimmer and taller, is the same arithmetic — remembering that grain does not sit like a liquid, and a conical roof is a separate solid (the cone calculator next door). A drinks can is roughly 3.2 cm inner radius and a little over 10 cm of useful height for 330 ml. A mental 5.2 cm by 10 cm already gives about 850 ml, far too much; the check by eye is worth doing.

Gas bottle, roller, round post, cylindrical aquarium: if the base is a circle and the wall goes up straight, this page. If the wall leans, the solid is a cone or a frustum. If the base is a rectangle, it is a cuboid. A round vessel with no distinguished axis is a sphere.

Worked case: radius 3, height 8

Radius 3, height 8, one unit throughout. Metres, for a tank-sized picture.

V = π × 3² × 8 = 72π ≈ 226.2 m³

Slat = 2π × 3 × 8 = 48π ≈ 150.8 m²

Stot = 2π × 3 × (3 + 8) = 66π ≈ 207.3 m²

The two bases: 2 × π × 9 = 18π ≈ 56.5 m². 150.8 + 56.5 = 207.3, as it should. In centimetres the same figures would be 226.2 cm³ — a small glass, not a tank. The unit is not decoration. A cone on the same base and height takes only a third: 24π ≈ 75.4 m³. That link is exact, not a rule of thumb.

Cubic metres into litres

1 m³ = 1,000 L. The 3-by-8 cylinder in metres is about 226,200 L. In centimetres, 72π cm³ ≈ 0.226 L. Same formula, a factor of a million between them (100 cubed).

1 L = 1 dm³ = 1,000 cm³  ; 1 m³ = 1,000 L

For a tank, the quiet route is: lengths in metres → m³ → × 1,000 = litres. A bucket 30 cm across and 30 cm deep: r = 0.15 m, V = π × 0.15² × 0.30 ≈ 0.0212 m³ ≈ 21 L. That looks like a bucket, so the conversion probably survived. Mixing centimetres with metres inside πr²h is how a cistern becomes a cup on paper.

A cone on the same base and height is one third

The most useful link between the two solids. A right cone of radius r and height h has volume (1/3) πr²h. The matching cylinder is πr²h. Exact ratio: one third. Archimedes had it; Cavalieri’s principle* lets the same fact be seen without a full integral: cross-sections that shrink linearly in radius shrink as the square in area, and the integral of x² from 0 to 1 is 1/3.

At bottom, a conical heap of sand inside a cylindrical silo, if the heap reaches the wall, is nowhere near a full silo. A funnel filled to the brim holds three times less than the cylinder that wraps it. For slant height and the frustum, the cone page is the right tool. The family of solid-geometry calculators keeps the same unit hygiene throughout.

Glossary

Net
The cylinder unfolded into the plane: a rectangle for the wall, plus two discs if the ends are included. The rectangle’s sides are the height h and the circumference 2πr.
Right circular cylinder
A cylinder whose bases are discs and whose side generators stand perpendicular to those bases. The formulae on this page assume that case. An oblique cylinder has the same volume for the same base and perpendicular height, but not the same lateral area.
Circumference
The length of the circular base, 2πr. It becomes the width of the unrolled label. Diameter × π is the same length.
Lateral surface
The curved wall alone, 2πrh, with neither lid nor base. Total surface adds the two discs: 2πr(r + h).
Cavalieri’s principle
Solids of equal height whose cross-sections parallel to the base have equal area have equal volume. It is why a cone is one-third of the wrapping cylinder, and why a sheared cylinder keeps the same volume.

Related calculators