Calculate Total Porosity of a Rock
Total porosity measures the share of a rock's volume occupied by voids (pores, cracks, gaps between grains) rather than solid matter. It governs the rock's ability to store water, oil or gas, and influences its mechanical strength and bulk density.
Two ways to measure it: from already known volumes (pore and total), or by the saturation method — the sample is weighed dry, then saturated with water, and the pore volume is derived from the mass of water absorbed.
Measurement method
Starred terms are unpacked in the glossary below the article.
Total, connected and effective porosity: three different voids
Porosity is “how much of this rock is not solid”. Which voids are counted is the whole argument.
- Total porosity* φt — every void, isolated vesicles included, over bulk volume. Crush the sample, or combine grain volume from a helium pycnometer with a bulk volume, and this is the number being sought.
- Connected (open) porosity — voids that talk to the outside, which water or a saturating brine can enter. The saturation method on this page measures that, not the sealed bubbles.
- Effective porosity* — the share that actually moves fluid under a gradient. Hydrogeologists often mean drainable pore space (specific yield). Reservoir engineers subtract clay-bound and capillary-irreducible water from φt. Same English phrase, two slightly different subtractions; which one was used has to be said.
φt = Vall voids / Vbulk · φopen = Vconnected / Vbulk · φe ≤ φopen ≤ φt
A vesicular basalt can look “high φ” on a crushed grain-density calculation and give almost nothing on a water flood. Isolated pores store; they do not deliver.
Why porosity is the tank and permeability is the tap
No pore volume, no reservoir, no aquifer. φ is the tank. Permeability* is the tap. The two are conflated because both live in the same fabric, but a full tank with no tap is a sealed trap, and a tap with no tank is a fracture in granite that runs dry by Thursday.
Storage capacity in a unit volume is φ × Sfluid. A sandstone at 22% porosity, 70% water saturation, holds 0.15 of its bulk volume as water — 150 L/m³. Fill those same pores with oil at So = 0.65 and the conversation is stock-tank, not well-yield. Pore-throat size then sets capillary pressure, which sets how tall an oil column a seal can hold, and how much water stays stuck as Swi. Porosity without a saturation and a throat-size story is a percentage looking for a job.
Measuring bulk volume without flooding the pores
Vtotal is the awkward input. Dunk an open sandstone and water walks into the pores; the “bulk” volume inferred from buoyancy is then too small. Two honest work-arounds:
- Coat the dry sample — thin paraffin, wax, or a spray lacquer — then hydrostatic weighing of the sealed envelope. Subtract the coat volume. Fragile, vuggy, or highly porous pieces belong here.
- Helium pycnometer on a plug gives grain volume (helium reaches open pores, not the solids). Pair that with a callipered or coated bulk volume and both φopen and φt are recovered, depending on whether any pores stayed closed to helium.
A “quick dunk” on a reservoir core is a moving target. Coat it, or saturate it on purpose and write the protocol on the sheet.
Saturation method: oven, vacuum, three masses
On the bench this is the workhorse for open porosity. Three masses, one density of water — if each step is given enough time.
- Dry at 105 °C to constant mass (often overnight). That is mdry. Clay-rich rocks may need a gentler temperature if the fabric is not to be wrecked; the temperature is noted.
- Saturate under vacuum, then leave the plug in de-aired water until the mass stops climbing. Wipe to surface-dry (SSD): shiny film gone, pores still full. That is msat.
- Volume from geometry, from a coated dunk, or from an immersed weighing of the saturated plug: Vbulk = (msat − mimmersed) / ρwater.
Vpores = (msat − mdry) / ρwater
φopen = Vpores / Vbulk = (msat − mdry) / (msat − mimmersed)
This page asks for Vtotal as a separate number: a calliper volume or a coated volume can then be brought in. The three-weighing identity above is the same arithmetic with Vbulk measured in the bath.
If msat is still rising at the weighing, the pores are not full and φ comes out low. Vacuum plus patience beats a longer formula.
Sorting versus grain size: why a dirty sand holds less
Mean grain size gets the headlines. Sorting does the damage.
A well-sorted beach sand packs like ball bearings: depositional porosity commonly 35–45%. A poorly sorted sand — coarse framework, silt and clay in the throats — uses those fines as a free cement. The big grains still occupy most of the volume; the small ones occupy the space that used to be pore. A glacial till can sit near 15% before anyone has compacted it. A fine well-sorted silt can out-porose a coarse dirty gravel. Diameter is not the predictor; the gap between the coarsest and finest fractions is.
Cement after burial (quartz overgrowths, calcite, authigenic clay) then spends the remaining porosity. Sorting sets the starting point; diagenesis spends it.
Primary versus secondary porosity
Primary porosity* is born with the rock: intergranular space in a sand, vesicles in a lava, shelter pores under a shell. It is often still visible on a blue-dye thin section.
Secondary porosity is later work. Joints and unloading fractures. Karst in limestone — moulds, vugs, conduits — that can take φ from 8% to something a well-log interpreter will not believe until a cave map is on the table. Dolomitization, which shrinks calcite into dolomite and sometimes leaves intercrystalline pores. Dissolution of feldspar in a buried arkose. Secondary porosity is patchy, which is why two plugs a metre apart disagree and why a dual-porosity model exists.
A granite with φt < 1% can still be an aquifer if the fracture net is connected. A chalk with φt = 35% can still be a seal if the throats are tiny. Origin of the pores says which of those stories applies.
Compaction with burial: Athy-type decline
Load a sediment and the pores lose. Grains rearrange, ductile lithics squash, pressure solution eats contacts and dumps the dissolved load as cement a millimetre away. The trend with depth is roughly exponential (Athy-type), not a straight line, and shales collapse faster than clean sands.
φ(z) ≈ φ0 · e−c z
A surface sand at 40% may be 18–22% at 1.5 km and under 10% at 4–5 km if quartz cement has been busy. Overpressure can freeze a higher φ to greater depth — a gift, not a law. A ticket showing 30% at 4 km in a normally pressured quartzose sand is a reason to ask how the sample was handled before the basin model is rewritten.
Porosity is not permeability
φ stores. Permeability k lets fluid move under a pressure gradient (darcy, millidarcy, m²). Hydraulic conductivity K folds in the fluid: viscosity and density. The same rock is a different K for water, brine, oil or gas.
K = (k · ρ · g) / η
A smectitic shale may show 20–40% porosity and microdarcy — or worse — permeability: the pores are there, the throats are not. A fractured granite may show 0.5% porosity and a well that flows, because k lives on the joints. A reservoir needs both a φ that pays and a k that produces. Kozeny–Carman-type links between the two assume a well-behaved intergranular fabric; they fail on vugs and on fractures, which is most of the interesting rocks.
Typical values by rock type
Open porosity, order of magnitude, dry of miracles:
- Sandstone — 15–30% when well sorted and moderately cemented; 5–15% when dirty or tightly cemented; uncompacted sand can still sit near 35%.
- Limestone and dolostone — 5–25% as a working band; reefal and karst intervals go much higher, locally.
- Shale — 5–20% total, almost none of it effective in the petroleum sense until a stimulated mudrock play is in view.
- Granite, massive basalt, gneiss, marble — typically < 1–3% primary. Weathering rinds and joints are another rock.
- Vesicular basalt — 10–30%; pumice — 50–80%, and some of it is isolated.
The band is a sanity check on a lab ticket, not a licence to skip the lab ticket.
Worked example: a sandstone plug
Sandstone plug, 1,500 m burial. Oven-dry, then vacuum-saturated in water at 20 °C (ρwater = 0.9982 g/cm³).
- mdry = 215.40 g
- msat = 238.70 g
- mimmersed = 135.20 g
Vpores = (238.70 − 215.40) / 0.9982 = 23.34 cm³
Vbulk = (238.70 − 135.20) / 0.9982 = 103.69 cm³
φopen = 23.34 / 103.69 = 22.5%
22.5% at 1.5 km is a respectable reservoir sandstone if the throats are clean. Dry bulk density is 215.40 / 103.69 ≈ 2.08 g/cm³, which matches a quartz framework with open pores, not a tight greywacke. Next measurements, not this one: gas permeability, a thin-section look for pore-lining clay, and a grain-density pycnometer run against which φt and φopen can be compared.
φ ≈ 1 − ρb / ρg
With ρg ≈ 2.65 g/cm³ for a quartzose plug, 1 − 2.08/2.65 ≈ 21.5%, within lab scatter of the 22.5% from saturation. Agreement is the expected result on a clean sand; disagreement is the clay-bound or closed-pore story.
North Sea reservoir sandstone: Brent, Forties, Rotliegend
UKCS core reports treat 20–28% as a working band for clean Brent (Middle Jurassic) and Forties (Paleocene) sandstones at 2–3 km. That is the tank that paid for the North Sea. BGS memoirs and operator SCAL packs quote helium porosity on 1-inch plugs, then gas permeability; the two are plotted together, not assumed from a Kozeny formula.
Rotliegend (Permian) aeolian sands of the southern North Sea can sit in the same φ band and still produce poorly if illite bridges the throats. A 22% Forties plug with 200 mD and a 22% Rotliegend plug with 2 mD are the same tank and two different taps. The calculator on this page does not see that; a thin section and a perm report do.
Bakken and shale porosity: a different kind of void
The Bakken (Williston Basin) and analogue mudrock plays (Eagle Ford, Haynesville, UK Bowland in the BGS assessment) carry 4–10% total porosity, much of it in organic matter and in pores a few tens of nanometres across. Water saturation by the method on this page understates that volume: oil-wet organics and clay-bound water do not fill like a Brent pore. Helium or NMR, plus a crushed-rock GRI-style protocol, is the industry answer.
Effective porosity in a shale-oil sense is not specific yield. It is the hydrocarbon-filled fraction that a fracture stimulation can drain. A Bakken core at 6% φt can outperform a 22% sandstone if the organic pores are oil-wet and connected after frac. Quoting “6% — tight sandstone” on a Bakken ticket is a category error. The geochemistry of the organic matter (TOC, maturity) belongs on the same sheet as the porosity.
Thin-section porosity versus what the balance sees
Blue-dye impregnation on a thin section, then a point count, is porosity by the Delesse* principle: area fraction on the slide estimates volume fraction in the rock. Pore shape is visible — intergranular versus vug versus fracture, clay bridges, overgrowths eating throats — which saturation never tells.
What the microscope cannot resolve is missed, and grain-pluck pits can be counted as pores if the grind was clumsy. On the bench, saturation plus bulk volume is blinder about geometry and more honest about volume, down to the pores the dye never reached. Report both when possible. The modal count and the porosity count can even share a grid, provided “pore” is a phase on the sheet.
Closed vesicles, helium, water, and the gap
Water saturation under vacuum fills connected pores. Helium in a pycnometer fills almost every open pore, including some throats water is slow to enter. Neither enters a sealed vesicle in a basalt or a closed mould in a tightly cemented grainstone.
φt − φopen is that isolated fraction. In a massive granite it is noise. In a flow-top scoria it is the difference between “this rock should float” and “this rock takes water”. If the two porosities disagree by more than lab error, the rock has a closed-pore story — write it down before the sample goes into a flood test and recovery comes back dead.
Glossary
- Total porosity (φt)
- All void space, connected or not, divided by bulk volume. From grain density plus bulk density: φ ≈ 1 − ρb/ρg.
- Effective porosity
- The fraction of bulk volume that actually transmits fluid. Hydrogeology often means drainable pores (specific yield); reservoir work subtracts clay-bound and irreducible water. The two are not identical.
- Permeability (k)
- The ability of the rock to let fluid move under a pressure gradient, in darcy, millidarcy or m². Distinct from porosity, which only stores.
- Primary porosity
- Void space formed with the rock: intergranular pores in a sand, vesicles in a lava, shelter pores in a limestone. Secondary porosity is later: fractures, karst, dissolution moulds.
- Delesse principle
- On a random section, the area fraction of a phase (here, pore space dyed blue) equals its volume fraction in the rock. The same statement used for modal mineral counts.