EN

Entropy Change Calculator (ΔS)

Entropy measures the disorder of a system and the direction in which transformations naturally proceed. Its change ΔS is worked out differently depending on the situation. Pick the case that matches your problem, enter the data, and read ΔS with the full breakdown of the calculation.

Convention: ΔS > 0 means the system's entropy increases; heat gained (Q > 0) raises the entropy, heat released (Q < 0) lowers it.

Case and inputs

Type of calculation

Switch situation, then run the calculation again to update the fields.

Heating / cooling

Result

  • Entropy change ΔS 779.5 J/K
  • Direction Entropy ↑
Mass m 1.000 kg
Specific heat c 4,186 J/(kg·K)
Initial temperature T₁ 293.15 K
Final temperature T₂ 353.15 K
Heat exchanged Q 251,160 J
Entropy change ΔS 779.5 J/K

ΔS = m · c · ln(T₂ / T₁)

Understanding entropy and its change

Entropy S is a state function. Its unit is the joule per kelvin (J/K). A single value of S is not something you read on a gauge; what you can compute, and what the second law talks about, is the change ΔS between two states. Clausius's definition is the starting point: for a reversible exchange of heat,

dS = δQrev / T

Divide the heat by the absolute temperature at which it crosses the boundary, and you have dS. All four modes on this page are that integral, done for a situation simple enough to finish by hand. T is always in kelvin. A Celsius reading has to be shifted by 273.15 before it goes in the denominator or in a logarithm.

The four situations covered

  1. Heat at constant temperature — a bath, a phase change, any isothermal swap. ΔS = Q / T. One division, provided T really does not move.
  2. Heating or cooling a body — T changes, so you integrate with Q = m c dT: ΔS = m·c·ln(T₂/T₁). The log is doing real work: the same 10 K rise at 10 K creates more entropy than the same 10 K rise at 100 K.
  3. Change of state — melt, freeze, boil, condense, at the transition temperature. ΔS = ± m·L / T. Plus when the body takes heat in (melting, vaporising), minus when it dumps heat (freezing, condensing).
  4. Ideal gas between two states (T, P): ΔS = n·Cp·ln(T₂/T₁) − n·R·ln(P₂/P₁). Drop the pressure at constant T and entropy rises — the gas has more volume to wander in. The ideal gas law is sitting underneath that second term.

The second law

For an isolated system, every real process obeys ΔS ≥ 0. Entropy stays put only in the reversible ideal; it grows in anything you can actually run. This calculator reports ΔS of the system you typed. That number can be negative — a fridge makes the food's entropy fall. The second law is not broken. The kitchen's entropy rises by more, and the universe's total still climbs:

ΔSuniverse = ΔSsystem + ΔSsurroundings ≥ 0

To decide whether a process is spontaneous, you need both sides. A negative ΔS_system with no number for the surroundings tells you nothing about direction. The Carnot limit is the same idea in engine clothes: a reversible cycle has ΔS_universe = 0, and no real engine gets there.

Why a logarithm, not just ΔT

If c is constant, δQ_rev = m c dT, so ΔS = m c ln(T₂/T₁). Equal temperature steps are not equal entropy steps. Warming 1 kg of water from 280 K to 290 K gives m c ln(290/280) ≈ 147 J/K. The same 10 K from 350 K to 360 K gives only ≈ 118 J/K. Heat dumped into a cold body disorders it more than the same heat dumped into a hot one. That is why the Clausius integral divides by T, and why a 10 °C rise typed as “10 / 10” in Celsius would be a different kind of wrong.

A useful check: T₂ = T₁ means ln(1) = 0, so ΔS = 0 for pure heating with no temperature change — which is tautological, and a good sign the formula is not inventing entropy out of nothing.

Entropy created by irreversible thermal contact

Two blocks, T_hot and T_cold, put in contact and left until they equalise. Each block has its own ΔS = m c ln(T_eq / T_start). The hot one loses entropy, the cold one gains more than that, and the sum is positive. That surplus is entropy created by the irreversible heat flow. A reversible path between the same end states — a Carnot engine run between them, infinitely slowly — would transfer the same energy with ΔS_universe = 0.

The calculator's heating mode, applied to each body and added, is how you see that creation. The mixing temperature from Q = m c ΔT gives T_eq first; the logs give the two ΔS values afterwards. Skip the logs and you only know that heat moved, not how much irreversibility it cost.

The third law: S heads for zero as T heads for 0 K

Nernst, Planck: the entropy of a perfect crystal approaches a constant, taken as zero, as T → 0 K. That is why we can talk about an absolute S and not only ΔS, at least on paper. It is also why ln(T₂/T₁) becomes savage if T₁ is tiny: a little heat at a millikelvin is a lot of entropy, and you cannot actually reach 0 K by a finite number of steps.

This page does not tabulate absolute entropies from statistical mechanics. It computes changes along the four classical paths. For a standard-molar-entropy look-up (S° of a compound at 298 K), you want a data book, not this form.

J/K for the system, J/(kg·K) on a spec sheet

ΔS here is extensive: double the mass, double the entropy change. Specific entropy s = S/m is the intensive cousin, in J/(kg·K), which is what steam tables print. Molar entropy is J/(mol·K), which is what chemistry tables print. Same quantity, divided by m or by n. If you came here with a specific value from a Mollier chart, multiply by the mass before comparing with the number in the result box.

The logarithmic formulas (heating, ideal gas) assume a constant heat capacity over the interval, and the ideal-gas model for the last case. Stretch the range, or sit next to a phase change, and c(T) moves: the log with a single c is then only a first cut. T in those formulas is kelvin, not a Celsius reading copied across.

Related calculators