Shear Stress Calculator: Pins, Bolts & Joints
When two joined parts try to slide past each other, the pin, bolt or dowel connecting them is sliced across its axis: that is shear. The shear stress is τ = F/A, where A is the total area of the sheared sections — and that is where the mistakes hide: number of fasteners, single or double shear, shank or threaded cross-section. This calculator handles the complete joint and returns the number of fasteners needed for the safety factor you are aiming at.
A material resists shear less well than tension: its shear yield limit is about 58% of Re (von Mises criterion: τe = Re/√3).
Load and joint
Shop-floor terms with an asterisk are collected in the glossary.
Shear: the material is sliced, not pulled
Shear slides the metal parallel to the cut, the same motion as the two blades of a pair of shears. A pin, a bolt, a dowel or a rivet passes load from one plate into the next through the section that lies on that sliding plane. Average shear stress* is τ = F / A. The shear area* A adds every cut that takes part — number of fasteners, times number of planes, times the area of one cut.
τ = F / (n × A₁ × planes) · τe = Re / √3 · s = τe / τ
In a ductile metal the shear yield sits below the tensile yield. Re itself comes from a tensile coupon; τe has to be inferred from a yield criterion rather than read off that test. This page uses von Mises, τe = Re / √3 ≈ 0.58 Re. A material that is happy at 640 MPa in tension starts to slide at about 370 MPa in pure shear. Compression is the push along the member, not a slice across it.
The planes are counted before the fasteners. Miss a factor of two and the joint is either twice as strong as this shear check suggests, or only half.
Single shear or double shear: the forgotten factor of two
- Single shear* — two lapped plates, one bolt. One sliding plane, at the contact. A = n × π d² / 4.
- Double shear* — a clevis*: the middle part sits between two straps, and the pin is cut on two planes at once. A doubles, τ halves. Cylinder pins, shackles, a fork-end rod: almost always this arrangement. The second plane is free capacity.
A strap-and-pin that looks like a clevis, yet leaves a gap on one side, is single shear plus a bending moment on the pin. The formula on this page does not include that moment. Where the straps do not hug the middle part, the pin carries bending together with shear, and the bending stress at the middle of the pin can govern.
Riveted lap joints are single shear. A butt joint with two cover plates is double shear. Old steel bridges were sized on that split long before τ = F/A was a line on a calculator.
Why Re / √3? Tresca, von Mises, Mohr
Yield in a ductile metal is a three-dimensional event. Two classical criteria, one picture.
- Tresca — yield begins once the maximum shear stress reaches Re / 2. Conservative, easy to apply, a hexagon in the Mohr / principal-stress plane. Pure shear: τe = 0.50 Re.
- von Mises — yield begins once the distortional energy reaches the tensile value. The limit surface is a smoother ellipse. Pure shear: τe = Re / √3 ≈ 0.577 Re. Closer to what mild steel does in a torsion coupon.
- Mohr's circle — a tensile test is a circle from 0 to Re. A pure-shear test is a circle centred on the origin with radius τ. Tresca is “the circle must not reach Re/2”. von Mises is a slightly larger allowance.
The 15% gap between 0.50 and 0.58 is smaller than the scatter on Re itself. von Mises is the criterion applied here, the usual default for ductile steels and aluminium. Joint codes (Eurocode 3 Table 3.4, AISC J3) do not quote √3: they publish a shear factor already calibrated on tests, of the same order, then reduce it with partial factors. A conservative hand check is the Tresca one-line version: τadm = 0.5 Re / s.
τe, von Mises = Re / √3 ≈ 0.58 Re · τe, Tresca = Re / 2 = 0.50 Re
Worked examples
- Two M12 grade 8.8 bolts, single shear — A = 2 × 113 mm², τe ≈ 370 MPa. The joint yields around 84 kN. At s = 2 the allowable hang is about 42 kN, a little over four tonnes, provided the shear plane is on the shank.
- Ø6 dowel in a clevis (double shear), S235 — A = 2 × 28.3 mm², τe ≈ 136 MPa, elastic capacity ≈ 7.7 kN. A small pin, two planes, only a modest hang.
- Shear plane through the thread — an M12 drops from 113 mm² on the shank to 84.3 mm² in the thread. A quarter of the capacity is gone. The unthreaded length belongs at the joint plane; otherwise the stress area is the figure to enter.
The minimum fastener count this form prints is F divided by the allowable load of one fastener at the target s. The count is rounded up. The plate needs a separate check: the bolt is not always the weak link.
Reading a bolt grade (X.Y)
Carbon-steel bolts to ISO 898-1 are read from the head marking. The first digit × 100 is the tensile strength Rm (“8.8” → 800 MPa). The product of the two digits × 10 is the yield Re (8 × 8 × 10 = 640 MPa). A 10.9 reaches Re = 900 MPa at the same diameter — often cheaper than stepping up to M16. A 12.9 is 1,080 MPa, on a more brittle temper: serviceable as a cap screw, and sensitive to hydrogen embrittlement and over-torque.
Stainless fasteners (ISO 3506) use a different marking. A2-70, A4-80: the letter is the alloy, the number is Rm/10. A4-70 sits near Re ≈ 450 MPa, A4-80 near 600 MPa. They do not reach 10.9 or 12.9. Corrosion is the reason to choose them, not a contest on Re. An “8.8” is not ranked against an “A4-80” by the numerals. Only the stated Re shows which shank is stronger.
The drop-down on this page is already that decoded Re.
Grade 4.6 is a mild 240 MPa, shop-made pins in S235 are 235 MPa, a C45 key is 430 MPa. The material entered is that of the fastener, not of the plates — unless the pin was machined from the same bar as the fork.
Bolt shear in the codes, not only F/A
Eurocode 3 writes Fv,Rd = αv fub A / γM2, with αv = 0.6 when the shear plane is in the shank; in the thread, 0.6 for grades 4.6, 5.6 and 8.8 and 0.5 for 4.8, 5.8, 6.8 and 10.9, with A the corresponding area. AISC 360 §J3 uses 0.450 Fu (threads included) or 0.563 Fu (threads excluded) on the nominal area, then a φ of 0.75. Both are cousins of von Mises, cast as an ultimate-strength check with a resistance factor, not a yield check with a safety factor s.
The 84 kN “yield” of two M12 8.8s above is not the code design resistance. The code numbers land in the same range — about 87 kN for the pair under Eurocode 3, about 76 kN under AISC with the threads excluded — and those are the numbers a building official expects. This calculator stays with the mechanics: τ against τe. It fits a machine pin, a clevis, a one-off bracket. For a structural bolted joint in a frame, the same inputs go into EN 1993-1-8 or AISC J3, with their αv and γM.
Preloaded (slip-resistant) joints are a third family. Until slip, friction carries the load, not shank shear. τ = F/A is the wrong model in service. It returns only as a backup after slip, at the ultimate limit state (ULS).
Bearing pressure and edge tear-out
The bolt can pass and the plate can fail. Two plate modes sit beside shear and often govern in aluminium, in thin steel, in a timber connection.
- Bearing pressure* — the shank crushes the hole wall. Average bearing stress σb = F / (d × t). In a soft plate (aluminium 2017A, a mild S235 against a 12.9 bolt) this limit arrives before the shank yields. Codes cap it with a factor on fu and a term for edge distance.
- Tear-out* / block shear — a plug of plate shears out toward a free edge, or a block rips around a group of holes. End distance, pitch, and net tension on the hole line all join in. A bolt 1.2 d from the edge is a tear-out waiting to happen, whatever τ in the shank says.
Fastener shear is all this page reports. Where the plates are thinner than about 0.8 d, or the plate material is weaker than the bolt, bearing and tear-out are worked by hand (or from the code tables) before the hardware is ordered. A 10.9 bolt in a 3 mm aluminium tab is a bearing problem wearing a shear costume.
τ = F/A is an average. Equal share between fasteners, and a uniform cut, are built into that figure. Misaligned holes, mixed grip lengths, a flexible cover plate: some shanks take more than 1/n of the load. The bolt check is not the whole joint — bearing on the plates and edge tear-out often govern in soft metals, and they are not in this number.
Tension and shear on the same bolt
A bracket with a vertical load and a prying* couple puts each bolt in tension and shear.
The two stresses interact. A common interaction (AISC J3.7, and a similar ellipse in Eurocode 3) is of the form (Fv/Fv,Rd) + (Ft/Ft,Rd) ≤ 1, or a squared version of the same idea. Filling the shear budget to 100% leaves nothing for the hang.
Pure shear is the only case treated here.
Where the joint also clamps a tensile load — a hanger flange, an eccentric bracket, a column base in uplift — tensile σ is taken on the tension calculator with As, τ is taken here, and the two are combined. Clearing a prying flange on shear alone is how a bolt ends up with a permanent neck.
Prying itself (the extra tension from a flexible flange trying to open) is not in either calculator. Thick flanges, a smaller pitch, or a backing plate: those are the usual cures, and they belong on the drawing, not in τ = F/A.
Glossary
- Shear stress
- Stress parallel to a cut, written τ. Shear force divided by the area of the cuts, not a pull along the member.
- Shear area
- The sliding area: number of fasteners, times number of planes, times the area of one section.
- Single shear
- One sliding plane. Two lapped plates and one bolt meet on that single cut.
- Double shear
- Two cuts through the same pin. The area doubles and τ halves for the same force.
- Clevis
- A middle piece between two outer straps, the pin crossing two shear planes. A gap on one side adds bending.
- Bearing pressure
- Crushing of the hole wall by the shank, σb = F / (d × t). In a soft or thin plate the limit can arrive before the shank yields.
- Tear-out
- A plug of plate shearing toward a free edge, or a block ripping around a group of holes. End distance, pitch and the net section all take part.
- Prying
- Extra tension when a flexible flange tries to open. Outside the pure-shear check and the plain tensile stress.