Circular Sector Area and Arc Length Calculator
A circular sector is the "pie slice" cut out of a circle by two radii and the arc that joins them. Its area and its arc length both follow from the circle's radius and the central angle that defines the slice.
Enter these two values: the calculator gives the sector's area, the arc length, and the length of the chord joining the two ends of the arc.
Radius and angle
Terms marked * are explained in the glossary that follows the article.
Why the compact formulae need radians
The compact formulae L = rθ and A = ½ r² θ only hold when θ is in radians*. Not degrees. One radian is the angle for which the arc length equals the radius. Once that is accepted, L = rθ needs no extra factor, and the area of a sector* is half the product of radius squared and that same angle.
The form will take degrees, radians or gradians. Conversion of the angle happens before the arithmetic — unlike the length unit, which is a label only. Working by hand from degrees, multiply by π/180.
θ (rad) = θ (°) × π ÷ 180
θ (rad) = θ (gon) × π ÷ 200
It is possible to stay in degrees if the fraction of the disc is put back in: L = (θ/360) × 2πr and A = (θ/360) × πr². Same mathematics, written as a share of the whole. Skipping the conversion is the classic trap: drop 60 straight into L = rθ and the result is 600 instead of 10.5.
The engine works in radians. An angle typed in degrees is converted once. Do not convert it a second time on paper.
Recovering the radius from area and angle
Given the sector area and the central angle, the radius comes back. Rearrange A = ½ θ r².
r = √(2A ÷ θ) (θ in radians)
Same rule as on the way out: θ in radians. Leave 60° as 60 and the square root is nonsense. The arc gives a second route: r = L ÷ θ. The two routes should agree. If they do not, the angle unit has slipped.
Take the positive root. A sector of radius zero is not a sector. The length unit only names the result: radius 10 stays 10; area comes back in that unit squared.
Circular segment versus sector
A segment* is not a sector. It is what remains of the sector after the isosceles triangle made by the two radii and the chord is cut away — the cap between the chord and the arc.
Compute the sector, compute the triangle (two sides r, included angle θ), subtract. With θ in radians the whole thing collapses to one line.
Segment area = (r² ÷ 2) × (θ − sin θ)
For a small angle the segment is a thin sliver: most of the sector's area sits in the triangle. At 180° the triangle flattens (the three points are collinear) and the segment becomes the half-disc. This page returns the sector and the chord; the segment is finished by hand. The triangle itself, if wanted as a standalone, is the three-side calculator or the triangle solver (two sides and the included angle).
Half-disc and quarter-disc
Two angles keep coming back, and the formulae collapse.
- Half-disc, 180° or π rad: area = πr² ÷ 2, arc = πr, chord = 2r (the diameter).
- Quarter-disc, 90° or π/2 rad: area = πr² ÷ 4, arc = πr ÷ 2, chord = r√2.
The half-disc is also half of the full disc. The quarter is a quarter. No need to fire up the sector calculator if the angle is exactly one of those two — except for the chord, which the circle page does not give. A 60° sector is a sixth of the disc, and the two radii plus the chord make an equilateral triangle of side r; that is the friendly special case below.
A sector of radius 10 and 60°
The defaults on the form. First, 60° in radians: 60 × π/180 = π/3 ≈ 1.0472.
- Arc: 10 × π/3 ≈ 10.472 (same unit as the radius).
- Area: (π/3 ÷ 2) × 10² = 50π/3 ≈ 52.360.
- Chord: 2 × 10 × sin(30°) = 10. Exactly the radius, because 60° makes an equilateral triangle.
So the triangle has sides 10, area (√3/4) × 100 ≈ 43.301. The segment, sector minus triangle, is about 9.06. It works neatly on paper because 60° is a friendly angle. At 47°, reach for the calculator. Entered as radius 10 and 60°, those three numbers — 52.360, 10.472, 10 — should come back. A sixth of the full disc is (1/6) × π × 100 ≈ 52.360, the same area written as a share of the circle; the two routes agreeing is the check that the degree-to-radian conversion actually happened.
Chord is not arc length
The arc* follows the circle. The chord* cuts straight across. For any given angle the arc is longer than the chord — they meet only at angle zero, which is not a sector worth drawing.
At 60°, as above, chord = r and arc ≈ 1.047 r. At 180°, chord = 2r (the diameter) and arc = πr ≈ 3.14 r. Mix them up on a taking-off and a curved edge has been costed as if it were a straight cut. The distance between two points is the chord, once the two endpoints are known as coordinates; it is not the arc.
Degrees, radians and gradians
One turn = 360° = 2π rad ≈ 6.2832 rad = 400 gon. Gradians still turn up in surveying. The radian is the natural unit for the formulae, and the one almost every programming language expects.
The angle selector on the form does the conversion. What it cannot do is guess that 1.047 was typed thinking degrees when the field is already in radians (that is 60°). Look at the unit before calculating.
π/3 is not 60. If the field is in degrees, type 60. For radians, switch the unit first, then type 1.0472.
A slope is a different angle, usually given as a ratio or a percentage, not as a central angle of a circle. Mixing the two is how a roof pitch gets fed into a sector formula that never asked for it.
A full turn recovers the disc
θ = 2π (or 360°): the sector is the whole disc again. Area = πr², arc = 2πr, chord = 0 (the two ends coincide). It is a useful check: if a sector formula does not recover the circle's area at 360°, the formula is wrong.
For the disc with no angle to worry about, the area and circumference calculator is the shorter route. A regular n-gon inscribed in the same circle is a stack of n isosceles sectors whose central angles are 2π/n; as n grows, those sectors fill the disc.
The rest of plane geometry on this site stays with polygons; this page is the one that keeps the curve.
Rolling a sector into a cone
Cut a sector and join the two radii. The figure becomes a cone (a funnel, a party hat). The arc of the sector becomes the circumference of the cone's base. If that base is to have radius ρ, the arc must equal 2πρ. With arc L = rθ, that is θ = 2πρ / r, with θ in radians.
A sector of radius 10 and 60° has arc ≈ 10.472. Rolled up, the base circumference is 10.472, so ρ ≈ 1.667. The slant height of the cone is the original radius, 10. The height of the cone then follows Pythagoras: √(10² − 1.667²) ≈ 9.86. A sector that is too open (θ near 2π) makes a flat, wide cone; one that is too closed (θ small) makes a needle. The central angle is the whole design.
The chord of the flat sector is not used in the roll. It is a check on the blank, before the join: if the measured straight cut between the two radii disagrees with 2r sin(θ/2), the angle on the drawing is not the angle that was cut.
The annulus is not a sector
An annulus* is a different cut: the ring between two concentric circles, area π(R² − r²), not a sector. A slice of that ring (an annular sector) multiplies the same difference by θ/(2π).
annulus = π (R² − r²) · annular sector = (θ / 2) (R² − r²) (θ in radians)
Do not write π(R − r)² — that is a disc of radius (R − r), a different shape. The width of the ring is R − r; its area is not π times that width squared. Outer radius 10, inner 6: the ring is π(100 − 36) = 64π ≈ 201.06. A 60° slice of it is one sixth of that, about 33.51 — not the 52.36 of the outer sector, because the inner disc has been punched out.
Glossary
- Radian
- The SI unit of angle. One radian is the central angle whose arc equals the radius. A full turn is 2π radians, about 6.2832, equal to 360° or 400 gon.
- Circular sector
- The “pie slice” bounded by two radii and the arc between them. Area A = ½ r² θ and arc length L = rθ, with θ in radians.
- Circular segment
- The cap between a chord and its arc: the sector minus the isosceles triangle made by the two radii and the chord. Area (r² / 2)(θ − sin θ), θ in radians.
- Arc
- The portion of the circle between two points, measured along the curve. Its length is rθ (θ in radians), always longer than the chord that joins the same two points.
- Chord
- The straight segment joining two points on the circle. Length 2 r sin(θ / 2). It is not the arc.
- Annulus
- The ring between two concentric circles. Area π(R² − r²). An annular sector is a slice of that ring, not a sector of the outer disc alone.