Concrete Block Calculator (Blocks per m²)
How many concrete blocks or bricks a wall needs depends on the area to cover, the block size and the thickness of the mortar joint that separates each block from its neighbours — a thicker joint slightly reduces the area each block actually covers, so it pushes the count up.
Enter the wall dimensions (minus any doors or windows) and the block dimensions: the calculator gives the number of blocks to buy, waste margin included, and an estimate of the mortar needed for the joints.
The wall and the block
Asterisks on trade terms open the glossary at the foot of the page.
Dense block, clay brick, aircrete
On a British site the words block and brick get used as if they named the same thing. They do not. A dense aggregate block is the large grey unit for a garage, a foundation wall, a party wall. A clay brick is the smaller fired unit, facing or common. Hollow clay blocks sit in between: lighter than dense concrete, more insulating, easier to chase for services, easier to snap if dropped.
This calculator does not care what the unit is made of. It counts rectangles separated by mortar. A 440 × 215 mm dense block, a matching aircrete* unit, a US CMU*, a clay brick — same arithmetic, different numbers in the three size fields.
What gets picked depends on the job. Below DPC*, in a retaining wall, anywhere wet and loaded: dense concrete, or engineering brick. A partition, an inner leaf that will be plastered: lightweight block or aircrete, because they can be lifted all day. Facing work that has to look like a house: clay brick, with the blockwork hidden behind or in the inner leaf.
Mixing heights in one course because a pack ran short is how a bed ends up out of level. Solid units still have a place. Padstones, the last course under a beam, a chimney breast, anything that takes a point load — hollow cores are a liability there. A few solids, bought or cut, beat filling cores with grout and hoping.
The UK 440 × 215 module and the US CMU
UK merchants live on one face size. US merchants live on another. Mixing the two on the same drawing is a classic way to order the wrong pack.
- UK concrete block — work size 440 × 215 mm on face. Thickness 100, 140 or 215 mm for most walls. With a 10 mm mortar joint the coordinating size* is 450 × 225 mm, which is 9.88 units per square metre. Everyone calls it 10.
- UK clay brick — work size 215 × 102.5 × 65 mm. Coordinating 225 × 75 mm on the stretcher face, about 60 bricks per m² for a half-brick wall. A completely different count. The form default of 50 × 20 cm has no business in a brick take-off.
- US CMU — the 8 × 8 × 16 in nominal unit. Actual (work) size is 7⅝ × 7⅝ × 15⅝ in, so the ⅜ in mortar joint brings it back to a neat 8 × 16 in module. Face area is smaller than a UK block, so more units per m² — roughly 12.1 per m² if converted, or 112.5 per 100 ft² of wall.
Aircrete often comes 440 × 215 mm in the UK, or 600 × 215 mm, and 620 × 250 mm on the Continent. Foundation blocks can be 440 × 215 × 275 mm or similar. The three fields want the real work size. The nickname on the merchant's ticket is not a dimension.
Default values on this page (50 × 20 × 20 cm) match a common European hollow block, not a 440 × 215 mm UK unit. Ordering from a UK yard means overwriting them: 440 mm × 215 mm × 100 mm, joint 10 mm, and the count will match what the merchant already knows.
Stretcher bond: why perpends never stack
Masonry is not a stack of aligned boxes. Blocks are laid in stretcher bond (running bond): each perpend* sits over the middle of the unit below. The diagram at the top of the page is that pattern.
A continuous vertical joint from damp-proof course to wall plate is a crack waiting for a bit of settlement. Stretcher bond stitches the courses together. Load from one block spreads onto two below it. That is why a wall is stronger than a pile of crates with the same number of pieces.
The price is cuts. Every other course ends on a half, a closer, or a sawn stub. The calculator divides an area. It has no idea that a 4.10 m length is not a multiple of 450 mm. That is what the waste margin is for.
English bond, Flemish bond, stack bond — they exist, mostly in facing brick. Stack bond in particular looks tidy and is weak unless bed-joint reinforcement is built in. For painted blockwork or a rendered garage, stretcher bond is the default. Aligning the perpends does not “save blocks”. It saves a week until the first crack.
Bond beams, lintels and DPC: outside this count
A wall is not a sheet of identical units. A few courses are something else entirely.
- Bond beam* — a course of U-blocks or knocked-out webs, filled with concrete and rebar, tying the wall at floor and roof level. Those units are ordered separately. The concrete and mortar mix calculator sizes the fill, not the block count.
- Lintels — steel, prestressed concrete, or a masonry lintel. They replace several blocks over a door or window. Deducting the opening area is not the same as deducting the lintel seating, which usually bears 100–150 mm past each jamb.
- Cavity trays, DPCs, wall ties — they do not change the block count much, but they do change how the first course starts.
- Quoins and cut reveals — extra labour, sometimes extra specials.
This page counts the skin. It does not design anything. Eurocode 6, BS EN 1996, TMS 402 for US work — none of that lives in a block quantity. If the wall is loadbearing, the layout of bond beams and lintels comes first. The block take-off comes after.
The result is not a full bill of quantities. Corner units, bond-beam blocks, lintels, cavity closers and coping stones are extra. Skipping the bond beam to “save six blocks” is not a saving. It is a wall that should not be built.
Cavity wall versus a single insulated leaf
UK housing is mostly a cavity wall*: clay brick or rendered block on the outside, blockwork on the inside, insulation in the gap (partial fill, full fill, or a blown-in retrofit). The calculator does one leaf at a time. Both skins mean two runs, with the right thickness each time — 102.5 mm brick outside, 100 mm block inside is a typical pair, not one 215 mm wall.
A solid wall of 215 mm dense block, or a single leaf of thick aircrete, still needs a decision on insulation: internal lining, external wall insulation, or a block that already meets the U-value on its own. Aircrete at 200–300 mm can be the whole wall in a garage or an extension. A dense 215 mm block on its own will not meet current dwelling standards. Insulation is added, or a different unit is picked. The thermal resistance calculator then stacks the layers, once the leaf and the insulation are chosen.
This page will not pass a SAP* calculation. It tells how many units to buy once the leaf is chosen. The thermal bit belongs in the specification, not in the mortar joint field.
Waste, closers and cut ends
Waste is not a tax. It is the pile of offcuts the job will actually make. A clean rectangle, no openings, length a multiple of 450 mm: 5% is plenty, sometimes less. A gable, three windows, a return, a reveal that lands awkwardly: 10%, and 15% if units are being broken with a hammer instead of a block saw.
Merchants sell halves and 100 mm closers. Using them at stops and openings is cheaper than sawing every other course out of a full unit — in time, if not always on the invoice. Plenty of small jobs ignore them and cut 440 mm blocks all afternoon. It works. It is wasteful.
The calculator applies a flat percentage and rounds up. It does not draw the bond. If the wall is 3.82 m long, divide by 0.45 m first (about 8.5 units). Alternate courses finish on a cut. A planned half-block beats a pack that runs out on Saturday.
Transit breakage is another matter. A cracked quoin, a crumbled aircrete corner at the bottom of the pack — 5% covers that on a small job. On a lorry-load, the check happens on delivery. That is not laying waste. That is a damaged-goods claim.
A garage gable 6 × 2.5 m
A garage gable in 440 × 215 × 100 mm dense blocks, 10 mm joints, a 2.50 m² door, 5% waste. The form defaults to 50 × 20 × 20 cm; the arithmetic is the same once those three fields are overwritten.
- Gross area — 6.00 × 2.50 = 15.00 m².
- Net area — 15.00 − 2.50 = 12.50 m².
- One unit plus joint — (0.440 + 0.010) × (0.215 + 0.010) = 0.450 × 0.225 = 0.10125 m².
- Raw count — 12.50 / 0.10125 ≈ 123.5 blocks.
- With 5% waste — 123.5 × 1.05 ≈ 129.6, rounded up to 130 blocks.
12.50 / [(0.440 + 0.010) × (0.215 + 0.010)] × 1.05 → 130 blocks
Joint mortar is a volume leftover: the 12.50 × 0.100 = 1.25 m³ prism, minus 123.5 solid blocks at 0.440 × 0.215 × 0.100 m each. About 83 litres of joints, roughly 180 kg of bedding mortar at the density this page uses. That is joints only — not the grout in a bond beam, not the render.
Leaving the door in, the order jumps to 148 raw, 156 with waste. Omitting the 2.5 m² opening puts the better part of an extra pack on the ticket. Deducting the door and omitting the lintel bearings and the cut reveals means Sunday is spent turning full blocks into jambs. The 130 is honest if lintels and U-blocks sit on a separate ticket.
Work size is not coordinating size
UK blocks are sold on work size — the dry unit, 440 × 215 mm. Drawings and setting-out use the coordinating size, 450 × 225 mm, which already includes a 10 mm joint. One is what gets held. The other is the grid the wall is designed on.
This form wants work size plus a joint thickness, because that is how a take-off is actually done. The boxes take 440 and 215 (in mm) and 10 mm of joint, not 450 × 225 with a zero joint. Putting the coordinating size in and adding a joint on top double-counts the mortar and under-orders the blocks.
US CMU is the same idea with different words: nominal 8 × 16 in versus actual 7⅝ × 15⅝ in. Again, the actual size goes in the boxes and the mortar in the joint field. Nominal in both places is the same trap.
Still, a 10 mm joint is not a cosmetic line. Dividing a square metre by 0.440 × 0.215 = 0.0946 gives 10.6 blocks and looks tidy. It is wrong. The 10 mm bed and perpend stretch the mesh to 450 × 225 mm, 9.88 per m². On 50 m² that gap is about 35 units — more than a pack.
Packs, cubes and how merchants sell
A 100 mm dense block often arrives in packs of 72, 90 or 100, depending on the works. A 130-unit order is two packs of 72 minus leftovers, or one of 90 plus a short pack. The packing is worth asking before the crane lorry is booked. Nobody enjoys “another eight by hand”.
Clay travels more fragile. A strap too tight, a pack sat on two battens, and the first course is already chipped. Storage is level, out of ruts, under a sheet that can breathe — not a puddle of condensation. Aircrete hates standing water even more: it drinks, it freezes, it crumbles.
Ordering the exact calculated number is a gamble. A spare pack, especially if the yard takes back a sealed one, costs less than a 40 km round trip on Sunday. Clean offcuts are worth keeping: a half of 440 always finds a reveal.
Conventional mortar bed versus thin-joint adhesive
The usual 10 mm bed is class M4 or M6 masonry mortar, cement-sand, sometimes with lime. It is the mass this page estimates. It forgives a 3 mm difference in height from one unit to the next. It eats time and sand. In practice the bag count comes from that leftover volume, not from a rule of thumb of “one bag per square metre”.
Ground aircrete and some clay blocks go down on thin-joint adhesive, 1 to 3 mm. The unit count then sits close to a dry-size division. The mortar mass on this page, computed as if 10 mm ran everywhere, becomes generous to the point of fiction. The joint field goes to 2 mm, or the bag estimate is noise.
All the same, a conventional 10 mm joint hides the odd 3 mm of difference between batches. Thin joint does not. Unground dense blocks on adhesive, to save a few bags, leave a wavy course. Two techniques in one wall, with no levelling course between them, is the surest way to a bed that will not sit.
At any rate the figure here is bedding and perpends, not pointing, not render, not floor screed. Hollow cores left empty — as they should be, unless a cell is being grouted — are already out of that volume, because the subtraction uses the block's overall rectangle, not the concrete only.
Glossary
- Aircrete
- Autoclaved aerated concrete (AAC). A lightweight block, often 440 × 215 mm in the UK, laid on thin-joint adhesive more often than on a 10 mm bed. It cuts with a hand saw and drinks standing water if stored badly.
- CMU
- Concrete masonry unit, the US trade name for a concrete block. The common 8 × 8 × 16 in unit is a nominal size; the actual unit is ⅜ in smaller each way so a mortar joint restores the module.
- DPC
- Damp-proof course. A horizontal barrier (bitumen, plastic, engineering brick) that stops ground moisture rising into the wall. Below it, dense units; above it, the wall the calculator is usually counting.
- Coordinating size
- Work size plus the mortar joint, used on drawings and for setting-out. A UK block of 440 × 215 mm has a coordinating size of 450 × 225 mm with a 10 mm joint. The form wants work size, not this grid size.
- Perpend
- The vertical mortar joint between the ends of two units in a course. In stretcher bond, perpends of one course sit over the middle of the units below, never in a continuous line.
- Bond beam
- A course of U-blocks or open-core units filled with concrete and reinforcement, tying the wall at floor or roof level. Ordered separately from the ordinary stretchers.
- Cavity wall
- Two leaves with a gap between them, usual in UK housing: facing brick or rendered block outside, blockwork inside, insulation in the cavity. Each leaf is a separate take-off.
- SAP
- Standard Assessment Procedure, the UK method for dwelling energy ratings. A block count is not a SAP input; U-values, thermal bridges and the construction build-up are.